Diffusionless transformation

Applied sciences
Chemical engineering
Materials science
Alloys

About
Privacy
Disclaimer

Graph Chatbot

Related publications (31)

Electron backscatter diffraction study of variant selection during ordering phase transformation in L1(0)-type red gold alloy

Roland Logé, Cyril Cayron, Margaux Nathalie Dominique Larcher

A shape-memory effect is known to appear in red gold alloys with compositions close to Au-Cu. The aim of this paper is to study by electron backscatter diffraction (EBSD) the variant selection in the A1 -> L1(0) transformation occurring under stress, in be ...

INT UNION CRYSTALLOGRAPHY2019

The interplay between deformation mechanisms in austenitic 304 steel during uniaxial and equibiaxial loading

Helena Van Swygenhoven, Efthymios Polatidis, Wei-Neng Hsu

The preferred deformation mechanisms with respect to the load path are studied in a medium stacking fault energy 304 austenitic stainless steel that exhibits both transformation induced plasticity and twinning induced plasticity. In situ neutron diffractio ...

2019

A High Resolution Digital Image Correlation Study under Multiaxial Loading

Helena Van Swygenhoven, Efthymios Polatidis, Wei-Neng Hsu

In this study, a miniaturized cruciform-shaped sample geometry which allows reaching high plastic strain under equibiaxial loading with reduced thickness at the test section is presented. The thinning method results in excellent surface quality that can be ...

SPRINGER2019

On the chevron morphology of surface martensite

Roland Logé, Cyril Cayron, Annick Pauline Baur

It is established that the annealing twin boundaries of austenite act as nucleation sites for the martensitic transformation. In the present study, we observe that in surface martensite the transformation only takes place for twin boundaries that are appro ...

2019

Microstructure and Mechanical Properties of a Multiphase FeCrCuMnNi High-Entropy Alloy

Roland Logé, Ali Shabani

A FeCrCuMnNi high-entropy alloy was produced using vacuum induction melting, starting from high-purity raw materials. The microstructure and mechanical properties of the as-cast FeCrCuMnNi alloy were studied, considering x-ray diffraction (XRD), scanning e ...

SPRINGER2019

Determining the Optimal Phase-Change Material via High-Throughput Calculations

Amina Matt

The discovery and optimization of phase-change and shape memory alloys remain a tedious and expensive process. Here a simple computational method is proposed to determine the ideal phase- change material for a given alloy composed of three elements. Using ...

2019

Residual stresses of friction melt bonded aluminum/steel joints determined by neutron diffraction

Jean-Marie Drezet

Near interfacial residual stresses are investigated in a joint composed of aluminum alloy and dual phase steel. A small step neutron diffraction scan was initially performed to determine the weld interface position along the measured transverse cross secti ...

ELSEVIER SCIENCE SA2019

Effect of Thermal Cycling on the Structural Evolution of Methylammonium Lead Iodide Monitored around the Phase Transition Temperatures

László Forró, Endre Horvath, Alla Arakcheeva, Gaétan Charles Antoine Giriat, Anastasiia Glushkova, Konstantins Mantulnikovs, Konstantin Semeniuk

Optoelectronic devices and solar cells based on organometallic hybrid perovskites have to operate over a broad temperature range, which may contain their structural phase transitions. For instance, the temperature of 330 K, associated with the tetragonal-c ...

2019

Experimental and theoretical investigation of crystallography and variant selection during massive transformation in Zr alloy

Cyril Cayron

Massive transformation, as a non-conventional solid-state phase transformation mode, is scarcely observed in metals with hexagonal closed packed (HCP) structure, especially in Zr and its alloys. In this study, however, we report the massive transformation ...

TAYLOR & FRANCIS LTD2019

Variant Selection in Fe-20Ni-1.8C under Bending

Roland Logé, Cyril Cayron, Annick Pauline Baur

Variant selection is commonly observed in martensitic steels when a stress is applied to the material during transformation. Classically, the selection phenomenon is modelled considering the work of the shape strain in the applied stress field. This shape ...

2018

Microstructural evolution and mechanical property development with nickel addition in low-carbon weld butt joints

Roland Logé, Cyril Cayron, Gaojun Mao, Rui Cao

Four metal powder flux-cored wires with added nickel (Ni) were designed to systematically investigate how Ni influences the microstructure and toughness in low-carbon bainitic weld metals (WMs). The microstructure was safely predicted by utilizing reasonab ...

2018

Page 2 of 2