Publications related to Amalgam (dentistry)

Slim: Explicit Slot-Intent Mapping With Bert For Joint Multi-Intent Detection And Slot Filling

Boi Faltings, Fei Mi, Fengyu Cai, Wanhao Zhou

Utterance-level intent detection and token-level slot filling are two key tasks for spoken language understanding (SLU) in task-oriented systems. Most existing approaches assume that only a single intent exists in an utterance. However, there are often mul ...

IEEE2022

Development of High-Strength Aluminum Alloys for Additive Manufacturing

Marvin Lennard Schuster

Metal additive manufacturing (AM) offers the possibility to rapidly produce complex geometries that are not achievable with conventional manufacturing methods. The two most common technologies, Laser Powder Bed Fusion (LPBF) and Direct Metal Deposition (DM ...

EPFL2022

Microstructure Selection in Laser Remelted Fe-C-Si Alloys

Wilfried Kurz, Philippe Gilgien

Laser surface remelting at various velocities has been employed to study the selection of microstructures of high-purity Fe-C-Si alloys containing nominally 3.2 to 4.2 wt.% C and 1 to 3 wt.% Si. The microstructure of the remelted region consisted of metast ...

WALTER DE GRUYTER GMBH2021

Imaging the Heterogeneity of the Oxygen Evolution Reaction on Gold Electrodes Operando: Activity is Highly Local

Sylvie Roke, Arianna Marchioro, Igor Nahálka

Understanding the mechanism of the oxygen evolution reaction (OER), the oxidative half of electrolytic water splitting, has proven challenging. Perhaps the largest hurdle has been gaining experimental insight into the active site of the electrocatalyst use ...

2020

High Performance Tri-gate GaN Power MOSHEMTs on Silicon Substrate

Elison de Nazareth Matioli, Jun Ma

We demonstrate high-performance GaN power metal-oxide-semiconductor high electron mobility transistors (MOSHEMTs) on silicon substrate based on a nanowire tri-gate architecture. The common issue of partial removal of carriers by nanowire etching in GaN tri ...

Institute of Electrical and Electronics Engineers2017

Metal artefact reduction in computed tomography images by a fourth-order total variation flow

Alfio Quarteroni, Elena Faggiano

Permanent metallic implants, such as dental fillings and cardiac devices, generate streaks-like artefacts in computed tomography (CT) images. In this article, we propose a strategy to perform metal artefact reduction (MAR) that relies on the total variatio ...

Taylor & Francis Ltd2016

On the micrometre precise mould filling of liquid polymer derived ceramic precursor for 300-µm-thick high aspect ratio ceramic MEMS

Jürgen Brugger, Rosario Maurizio Gullo, Jonas Grossenbacher

This paper describes a novel and scalable method for the fabrication of polymer derived ceramics (PDC) structures with high aspect ratio and micrometre scale features. Elastomeric micro-moulds composed of a filling pot are used to deliver via sacrificial m ...

Elsevier2015

Infiltration of tin bronze into alumina particle beds: influence of alloy chemistry on drainage curves

Andreas Mortensen, Ludger Weber, Alain Léger

The wetting of angular alumina particle preforms by Cu-Sn alloys is investigated by means of pressure infiltration experiments conducted at 1150 A degrees C, using a system enabling dynamic and precise measurements of the metal volume injected into the pre ...

Springer Verlag2014

Role of filling materials in a P-wave interaction with a rock fracture

Jian Zhao, Wei Wu

The purpose of this study is to investigate the role of filling materials (e.g., quartz sand and kaolin clay) in the interaction between a P-wave and a rock fracture. The specific fracture stiffness reflects the seismic response of a filled fracture, while ...

Elsevier2014

Isothermal Ageing of SnAgCu Solder Alloys: Three-Dimensional Morphometry Analysis of Microstructural Evolution and Its Effects on Mechanical Response

John Botsis, Joël Cugnoni, Milad Maleki

Due to the high homologous temperature and fast cooling rates, the microstructures of SnAgCu (SAC) solders are in a meta-stable state in most applications, which is the cause of significant microstructural evolution and continuous variation in the mechanic ...

Springer2014

Dynamic response of a rock fracture filled with viscoelastic materials

Jian Zhao, Wei Wu, Jianbo Zhu

Rock fractures filled with viscoelastic materials, such as sand, usually contribute to rock mass instability under the influence of seismic waves and dynamic loads. The purpose of this study is to verify that the specific fracture stiffness and the specifi ...

Elsevier2013

Optimized conditions for gas light interaction in photonic crystal fibres

Luc Thévenaz, Isabelle Dicaire

This paper presents helpful expressions predicting the filling time of gaseous species inside photonic crystal fibres. Based on the theory of diffusion, our gas-filling model can be applied to any given fibre geometry or length by calculating diffusion coe ...

The International Society for Optical Engineering2010

Analytical modeling of the gas-filling dynamics in photonic crystal fibers

Luc Thévenaz, Isabelle Dicaire

We present useful expressions predicting the filling time of gaseous species inside photonic crystal fibers. Based on the theory of diffusion, this gas-filling model can be applied to any given fiber geometry or length by calculating diffusion coefficients ...

Optical Society of America2010

Mechanical behaviour of diamond reinforced metals

Ludger Weber, Reza Tavangar Hamzehkolaei

Diamond reinforced metals with a diamond content of 55-60 vol.% were made by gas driven liquid metal infiltration. They were characterized with regard to their stiffness, strength and fracture toughness as a function of diamond particle size and matrix all ...

2009

Optical properties of metal-doped carbon based nanocomposite thin films: Comparing experiment to effective medium theories

Josef Andreas Schuler

Nanocomposite thin films exhibit interesting optical properties which differ from those of the pure constituents. Effective medium theories are used to model the dielectric function of the nanocomposite materials. We give an introduction to the theories of ...

2006

Influence of Ta and Ti Doping on the High Field Performance of (Nb,Ta,Ti)(3)Sn Multifilamentary Wires based on Osprey Bronze with High Tin Content

Davide Uglietti

Ta and Ti are the most widely used additions for technical Nb3Sn multifilamentary superconductors. These elements are known to influence grain growth, grain morphology and chemical composition in the A15 layer, hence the current carrying properties of the ...

Institute of Physics Publishing2006