Publications related to Sintering

Sinter-Resistant Nickel Catalyst for Lignin Hydrogenolysis Achieved by Liquid Phase Atomic Layer Deposition of Alumina

Jeremy Luterbacher, Songlan Sun, Farzaneh Talebkeikhah

Lignin hydrogenolysis is a key step in the sustainable production of renewable bio-based chemicals and fuels. Heterogeneous metal catalysts have led to high yields but they rapidly deactivate, notably due to nanoparticle sintering and carbonaceous deposit ...

2023

Liquid metal infiltration of silicon based alloys into porous carbonaceous materials Part-III: Experimental verification of conversion products and infiltration depth by infiltration of Si-Zr alloy into mixed SiC/ graphite preforms

Ludger Weber, Annapaola Parrilli, Caroline Hain, Alberto Ortona, Manoj Kondibhau Naikade

Porous carbonaceous preforms, made from graphite and silicon carbide (SiC) powders, with varying graphite powder mass fractions and particle sizes, were infiltrated at 1500 degrees C and 1700 degrees C by Si-8 at. pct Zr alloy to produce dense Si-Zr-SiC co ...

ELSEVIER SCI LTD2023

Dataset for 'Printed ecoresorbable temperature sensors for environmental monitoring'

Danick Briand, Nicolas Francis Fumeaux, James Alec Pierce Bourely, Melissa Kossairi

This data set contains the data collected during the FNS project Green Piezo (Grant no. 179064) in association with the recent publication entitled “Printed ecoresorbable temperature sensors for environmental monitoring”. This work aims to study the effect ...

Zenodo2023

Characterisation and hydration kinetics of beta-C2S synthesised with K2SO4 as dopant

Karen Scrivener, Franco Alberto Zunino Sommariva, Shashank Bishnoi, Sreejith Krishnan

In this study, a protocol for synthesising beta-C2S using K2SO4 as a dopant has been reported. Quantitative X-Ray diffraction was used to characterise synthesised samples. It was observed that it is possible to synthesise beta-C2S with high purity (>96 wt% ...

Pergamon-Elsevier Science Ltd2023

Printed ecoresorbable temperature sensors for environmental monitoring

Danick Briand, Nicolas Francis Fumeaux, James Alec Pierce Bourely, Melissa Kossairi

Electronic waste has become a pressing issue, necessitating sustainable solutions for the disposal of electronic devices. While the development of environmentally degradable electronics has gained attention, the fabrication of stable and performant sensors ...

2023

Vacancy segregation and intrinsic coordination defects at (111) twist grain boundaries in diamond

Carolina Baruffi, Christian Brandl

High radiation damage resistance has become increasingly important for applications of functional materials in harsh environments. The high radiation damage resistance diamond cubic carbon is a unique material which is considered for radiation environments ...

Pergamon-Elsevier Science Ltd2023

Theory of spontaneous grain boundary roughening in high entropy alloys

William Curtin, Carolina Baruffi

High Entropy Alloys (HEAs) are a new broad class of near-random solid solution alloys that can possess some impressive mechanical and physical properties including high stability against grain growth (i.e. low grain boundary (GB) mobility). Here, it is sho ...

PERGAMON-ELSEVIER SCIENCE LTD2022

Multiscale microshaping of functionally graded polymer-derived SiCN ceramics

Lorenz Hagelüken

Polymer-derived ceramics (PDCs) exhibit excellent properties and are compatible with many shaping techniques due to the liquid character of the preceramic polymers (PCPs). Furthermore, their properties are adjustable by modifying the precursor composition ...

EPFL2022

Thermal Sintering and Phosphorus Poisoning of a Layered Diesel Oxidation Catalyst

Oliver Kröcher, Davide Ferri

The tightening emission regulations have led to the development of commercial DOCs with zoned or layered formulations allowing to cover a wide range of functionalities (i.e. CO, HC and NO oxidation as well as HC or NOx trap). Aging phenomena in such comple ...

SPRINGER/PLENUM PUBLISHERS2023

The effect of pore microstructure on strength and chloride ingress in blended cement based on low kaolin clay

Karen Scrivener, Diana Londoño Zuluaga

The objective of this study is to analyse the mechanical and durability properties of a high-performance mortars based on low grade kaolin clay and the effect of electrical conductivity and pore microstructure on the chloride penetration resistance. A tota ...

ELSEVIER2022

From pulsed-DCMS and HiPIMS to microwave plasma-assisted sputtering: Their influence on the properties of diamond-like carbon films

Aïcha Hessler-Wyser, Johann Michler, Caroline Hain, David Brown, Thomas Nelis

The fabrication of high-hardness non-hydrogenated diamond-like carbon (DLC) via standard magnetron sputtering (MS) is often hindered by the low sputtering yields and ionisation rates of carbon, therefore investigations into pulsed alternatives of MS, else ...

ELSEVIER SCIENCE SA2022

On the structure of (111) twist grain boundaries in diamond: atomistic simulations with Tersoff-type interatomic potentials

Carolina Baruffi

In nanocrystalline diamond thin films, the high grain boundary density and the associated grain boundary properties may dominate the overall material behavior. In the present work, we systematically investigate (111) twist grain boundaries in diamond carbo ...

PERGAMON-ELSEVIER SCIENCE LTD2021

In-situ laser sintering for the fabrication of fully 3D printed electronics composed of elastomeric materials

Danick Briand, Rubaiyet Iftekharul Haque, Sébastien Lani, Ryan Mitchell van Dommelen, Olivier Rémy Henry Chandran

In-situ laser sintering can be used to locally sinter conductive inks in an uninterrupted process, enabling the embedding of printed electronics within 3D printed structures. In this work we apply a laser sintering method to create highly conductive silver ...

2021

Mechanistic Study on Thermally Induced Lattice Stiffening of ZIF-8

Wendy Lee Queen, Kumar Varoon Agrawal, Pascal Alexander Schouwink, Jian Hao, Mehrdad Asgari, Deepu Joseph Babu, Qi Liu

The flexibility of the ZIF-8 aperture, which inhibits a molecular cutoff of 3.4 angstrom, can be reduced by rapid heat treatment to obtain CO2-selective membranes. However, the early stages of the structural, morphological, and chemical changes responsible ...

2021

A round Robin-Highliting on the passivating contact technology

Franz-Josef Haug, Andrea Ingenito, Audrey Marie Isabelle Morisset, Aditya Chaudhary

The aim of this work is to demonstrate the maturity of the TOPCon technology by conducting a round-robin on symmetrically processed lifetime samples in the leading European PV institutes EPFL, ISC, CEA-INES, ISFH, IMEC and Fraunhofer ISE within the H2020 f ...

EDP SCIENCES S A2021

Particle-size segregation and rheology coupling in dense granular flows

Tomás Alfredo Trewhela Palacios

Dense granular flows -debris or pyroclastic flows, avalanches, granular flows in heaps, silos or rotating drums-are ubiquitous to many natural and industrial processes. Their grain composition is often polydisperse, with particles differing in shape, size ...

EPFL2021

Thermal coarsening of individual titanate nanowires and their assemblies: Surface vs. bulk diffusion

László Forró, Luca Rossi, Endre Horvath, Sergiy Katrych, Massimo Spina, Laurent Syavoch Bernard, Xavier Berdat

The thermal coarsening of titanate nanowires was investigated from room temperature to 1000 degrees C by AFM, SEM, XRD and Raman spectroscopy. Phase transformation kinetics and the external morphology were studied in two configurations: i) as individual an ...

2020

Joining of Oxide Dispersion-Strengthened Steel Using Spark Plasma Sintering

Cyril Cayron

Difficulties with joining oxide dispersion-strengthened (ODS) steels using classical welding processes have led to the development of alternative joining techniques such as spark plasma sintering (SPS). SPS, which is classically employed for performing sin ...

2020

Spark Plasma Sintering of Ceramics: From Modeling to Practice

Paul Bowen, Michael Stuer, Zhe Zhao

Summarizing the work of nearly a decade of research on spark plasma sintering (SPS), a review is given on the specificities and key factors to be considered in SPS of ceramic materials, based on the authors’ own research. Alumina is used primarily as a mod ...

2020

Enhanced strength and toughness of bulk ultrafine grained Cu by nacre-inspired lamellar structure

Roland Logé, Jun Wang, Chenguang Li

An ultrafine grained (UFG) bulk Cu with a novel nacre-inspired lamellar structure containing nano-bridges and aligned nanopores at inter-lamellar interfaces was fabricated by consolidation of a nanocrystal-attached ultrathin Cu flake powder by spark plasma ...

2020