Concept

Forensic polymer engineering

Forensic polymer engineering is the study of failure in polymeric products. The topic includes the fracture of plastic products, or any other reason why such a product fails in service, or fails to meet its specification. The subject focuses on the material evidence from crime or accident scenes, seeking defects in those materials that might explain why an accident occurred, or the source of a specific material to identify a criminal. Many analytical methods used for polymer identification may be used in investigations, the exact set being determined by the nature of the polymer in question, be it thermoset, thermoplastic, elastomeric or composite in nature. One aspect is the analysis of trace evidence such as skid marks on exposed surfaces, where contact between dissimilar materials leaves material traces of one left on the other. Provided the traces can be analyzed successfully, then an accident or crime can often be reconstructed. Thermoplastics can be analysed using infra-red spectroscopy, ultraviolet–visible spectroscopy, nuclear magnetic resonance spectroscopy and the environmental scanning electron microscope. Failed samples can either be dissolved in a suitable solvent and examined directly (UV, IR and NMR spectroscopy) or be a thin film cast from solvent or cut using microtomy from the solid product. Infra-red spectroscopy is especially useful for assessing oxidation of polymers, such as the polymer degradation caused by faulty injection moulding. The spectrum shows the characteristic carbonyl group produced by oxidation of polypropylene, which made the product brittle. It was a critical part of a crutch, and when it failed, the user fell and injured herself very seriously. The spectrum was obtained from a thin film cast from a solution of a sample of the plastic taken from the failed forearm crutch. Microtomy is preferable since there are no complications from solvent absorption, and the integrity of the sample is partly preserved. Thermosets, composites and elastomers can often be examined using only microtomy owing to the insoluble nature of these materials.

Official source

https://en.wikipedia.org/wiki/Forensic_polymer_engineering

About this result

This page is automatically generated and may contain information that is not correct, complete, up-to-date, or relevant to your search query. The same applies to every other page on this website. Please make sure to verify the information with EPFL's official sources.

Related courses (2)

MSE-352: Introduction to microscopy + Laboratory work

Ce cours d'introduction à la microscopie a pour but de donner un apperçu des différentes techniques d'analyse de la microstructure et de la composition des matériaux, en particulier celles liées aux m

MSE-451: Polymer morphological characterization techniques

Sample preparation and direct observation techniques (optical microscopy, AFM, electron microscopy) and their practical application to the study of morphology and microdeformation in polymers.

Related lectures (2)

Electron Microscopy: EDS and ESEM

Explores EDS and ESEM principles, x-ray detection, ionization efficiency, Moseley's law, and ESEM sample environments.

Electron Microscopy: ESEM

Explores Electron Scanning Electron Microscopy (ESEM) for imaging samples in various environments and studying phase transitions.

Official source

https://en.wikipedia.org/wiki/Forensic_polymer_engineering

About this result

Related courses (2)

MSE-352: Introduction to microscopy + Laboratory work

MSE-451: Polymer morphological characterization techniques

Sample preparation and direct observation techniques (optical microscopy, AFM, electron microscopy) and their practical application to the study of morphology and microdeformation in polymers.

Related lectures (2)

Electron Microscopy: EDS and ESEM

Explores EDS and ESEM principles, x-ray detection, ionization efficiency, Moseley's law, and ESEM sample environments.

Electron Microscopy: ESEM

Explores Electron Scanning Electron Microscopy (ESEM) for imaging samples in various environments and studying phase transitions.

Related publications (25)

Extraction and controlled functionalization of lignin for materials applications

Stefania Bertella

Lignin is a renewable aromatic polymer that due to its abundance and unique chemical structure is a promising candidate to replace aromatic materials that are currently sourced from fossil oil. The same structure of lignin poses however drawbacks for its v ...

EPFL2022

Biodegradation and Antimicrobial Properties of Zinc Oxide-Polymer Composite Materials for Urinary Stent Applications

Lorenzo Lucherini

Research advancements in the field of urinary stents have mainly been in the selection of materials and coatings to address commonly faced problems of encrustation and bacterial adhesion. In this study, polylactic acid (PLA) and polypropylene (PP) were eva ...

2020

Influence of cracking and rough surface properties on the transfer of forces in cracked concrete

Aurelio Muttoni, Miguel Fernández Ruiz, Max Tirassa

Aggregate interlocking is acknowledged as one of the most significant actions transferring shear forces in cracked concrete structures and has been investigated for several decades. Despite the many experimental programmes and previous efforts to develop m ...

2020

Related concepts (6)

Forensic materials engineering

Forensic materials engineering, a branch of forensic engineering, focuses on the material evidence from crime or accident scenes, seeking defects in those materials which might explain why an accident occurred, or the source of a specific material to identify a criminal. Many analytical methods used for material identification may be used in investigations, the exact set being determined by the nature of the material in question, be it metal, glass, ceramic, polymer or composite.

Ozone cracking

Cracks can be formed in many different elastomers by ozone attack, and the characteristic form of attack of vulnerable rubbers is known as ozone cracking. The problem was formerly very common, especially in tires, but is now rarely seen in those products owing to preventive measures. However, it does occur in many other safety-critical items such as fuel lines and rubber seals, such as gaskets and O-rings, where ozone attack is considered unlikely. Only a trace amount of the gas is needed to initiate cracking, and so these items can also succumb to the problem.

Trace evidence

Trace evidence is created when objects make contact, and material is transferred. This type of evidence is usually not visible to the eye and requires specific tools and techniques to be obtained. Due to this, trace evidence is often overlooked, and investigators must be trained to detect it. This type of evidence can link a victim to suspects and a victim or suspect to the crime scene. The importance of trace evidence in criminal investigations was shown by Edmond Locard in the early 20th century, with his exchange principle, that every contact leaves a trace.