Differential thermal analysis

Natural sciences
Chemistry
Physical chemistry
Thermochemistry

About
Privacy
Disclaimer

Graph Chatbot

Related publications (31)

Beam duct for the 1 MW neutral beam injector on TCV

Basil Duval, Stefano Coda, Yves Martin, Alexander Karpushov, Matthieu Toussaint, Frédéric Dolizy, Roberto Maurizio

The 1MW power of the neutral beam injector (NBI) enters the plasma of the Tokamak a Configuration Variable (TCV) through a duct. The original beam propagation model predicted a maximal heat flux on the internal faces of the duct below 350 kW/m(2), leading ...

2020

Effect of temperature on the water content of C-A-S-H in plain Portland and blended cements

Karen Scrivener, François Henri Avet

This study aims to investigate the change with temperature of the water content of the C-(A)-S-H of plain cement (PC) and Limestone Calcined Clay Cement (LC3). The water content was determined by various methods: thermogravimetric analysis (TGA), H-1-nucle ...

Pergamon-Elsevier Science Ltd2020

Visualizing the importance of oxide-metal phase transitions in the production of synthesis gas over Ni catalysts

Stéphane François Jean Poitel

Synthesis gas, composed of H-2 and CO, is an important fuel which serves as feedstock for industrially relevant processes, such as methanol or ammonia synthesis. The efficiency of these reactions depends on the H-2 : CO ratio, which can be controlled by a ...

2020

The effect of sodium hydroxide on Al uptake by calcium silicate hydrates (C S H)

Christian Ludwig, Barbara Lothenbach, Sonya Barzgar, Mohamed Tarik, Alessio Di Giacomo

To reduce the CO2 emissions from cement production, Portland cement (PC) is partially replaced by supplementary cementitious materials (SCM). Reactions of SCM with PC during hydration leads to the formation of CSH with more silicon and aluminum than in PC, ...

2020

Reusability of filtering facepiece respirators after decontamination through drying and germicidal UV irradiation

Véronique Michaud, David Vernez, Guillaume Suarez, Kiattisak Batsungnoen

Introduction During pandemics, such as the SARS-CoV-2, filtering facepiece respirators plays an essential role in protecting healthcare personnel. The recycling of respirators is possible in case of critical shortage, but it raises the question of the effe ...

2020

Synthesis, Characterisation and Crystal structure of a New Cu(II)-carboxamide Complex and CuO nanoparticles as New Catalysts in the CuAAC reaction and Investigation of their Antibacterial activity

Kurt Schenk, Farzaneh Fadaei Tirani

The bidentate carboxamide ligand N-(thiazole-2-yl) picolinamide (LH) was synthesized in the environmentally friendly ionic liquid TBAB, and the five-coordinated Cu-II-complex, [Cu(L)(2)(H2O)]center dot CHCl3 (1) was synthesized from LH and copper(II)acetat ...

2020

One-dimensional facile growth of MAPbI(3) perovskite micro-rods

Mohammad Khaja Nazeeruddin, Zubair Ahmad

One-dimensional microrods (4-5 mm) of PbI2 and CH3NH3PbI3 (MAPbI(3)) with unique structural and morphological properties have been grown at room temperature. X-ray diffraction (XRD) patterns of both types of micro-rods exhibit a hexagonal system (P3m1(164) ...

2019

Effect of surface modification of colloidal silica nanoparticles on the rigid amorphous fraction and mechanical properties of amorphous polyurethane-urea-silica nanocomposites

John Christopher Plummer, Nicolas Candau, Oguzhan Oguz, Stéphane Henri Florian Bernhard

Colloidal silica nanoparticles (NPs) modified with eight different silane coupling agents were incorporated into an amorphous poly(tetramethylene oxide)-based polyurethane-urea copolymer matrix at a concentration of 10 wt % (4.4 vol %) in order to investig ...

2019

Characterization of variable stiffness joints for adaptive structures

Gennaro Senatore

This paper presents a new strategy to control the structure dynamic response via a shift of the natural frequencies obtained through using variable stiffness joints. The joints are made of shape memory polymers and are fabricated through 3D printing. Stiff ...

Taylor & Francis2019

Impacting factors and properties of limestone calcined clay cements (LC3)

Karen Scrivener, Franco Alberto Zunino Sommariva, François Henri Avet, Julien Ston, Aurélie Rosine Favier, Hamed Maraghechi, Wilasinee Hanpongpun

This paper details the main factors influencing the performance of limestone calcined clay cements (LC3). The kaolinite content plays a major role in the rheological properties as well as strength development. Even in the presence of secondary phases, kaol ...

ICE PUBLISHING2019

Perovskite Solar Cells Based on Oligotriarylamine Hexaarylbenzene as Hole-Transporting Materials

Michael Graetzel, Shaik Mohammed Zakeeruddin, Ulf Anders Hagfeldt, Mona Shasti

A cobalt-catalyzed cyclotrimerization of bis(aryl)alkyne is used as an innovative tool to obtain hole-transport materials (HTMs). The novel HTM containing six units of oligotriarylamine (HAB1), characterized by UV-vis, cyclic voltammetry, DFT, and thermogr ...

AMER CHEMICAL SOC2019

Page 2 of 2