Fumed silica

Natural sciences
Earth science
Geology
Mineralogy

About
Privacy
Disclaimer

Graph Chatbot

Related publications (31)

Influence of low curing temperatures on the tensile response of low clinker Strain Hardening UHPFRC under full restraint

Emmanuel Denarié, Mohamed Abdul Hafiz

The tensile response of strain hardening UHPFRC under full restraint, subjected to curing temperatures of 20 °C, 10 °C, 5 °C, was investigated for two types of mixes with silica fume; Mix I with pure type I cement and Mix II with 50% replacement of cement ...

Pergamon-Elsevier Science Ltd2020

Investigation of femtosecond laser-tuned thermomechanical properties of fused silica

Pieter Vlugter

The thermomechanical properties of materials are among the most important properties for designing precision instruments, in particular for devices seeking high-dimensional stability, invariant temperature-elastic properties or low thermoelastic losses. De ...

EPFL2020

Modelling of the tensile behavior of SH-UHPFRC at low and high stress levels, under very low loading rates

Emmanuel Denarié, Mohamed Abdul Hafiz

The tensile behavior under low loading rates governs to a large extend the mechanical response of Strain Hardening Ultra High Performance Fiber Reinforced Concretes (SH-UHPFRC) at early age and long term, in applications of rehabilitation. A viscoelastic-v ...

2020

Advances in heterogeneous catalysis for the synthesis of polyoxymethylene dimethyl ethers

Christophe Jean Baranowski

Our society is engaged in a major shift towards more sustainable industries. The required transition from fossils to renewable resources with low greenhouse gas emission is specifically challenging in the transportation sector where high thermal efficiency ...

EPFL2020

Laser-induced densification of fused silica using spatially overlapping sub-30fs pulses

Yves Bellouard, Farhang Nabiei, Ya Cheng

Over the past several years, non-ablative femtosecond laser exposure with spatially overlapping (i.e., spatially cumulative) pulses has emerged as a key process in three-dimensional writing of patterns in bulk of dielectric substrates. When temporally non- ...

2020

Tensile response of UHPFRC under very low strain rates and low temperatures

Emmanuel Denarié, Mohamed Abdul Hafiz

This paper addresses the uniaxial tensile response of Strain Hardening Ultra High-Performance Fiber Reinforced Concretes (SH-UHPFRC) subjected to very low strain rates and low temperatures. The influence of four different strain rates; 1 × 10−5, 1 × 10−7, ...

Pergamon-Elsevier Science Ltd2020

Tensile response of low clinker UHPFRC subjected to fully restrained shrinkage

Emmanuel Denarié, Mohamed Abdul Hafiz, Amir Hajiesmaeili

This paper addresses the tensile response of Strain Hardening Ultra High Performance Fiber Reinforced Concretes (SH-UHPFRC) subjected to restrained autogenous shrinkage deformations under full and partial restraint conditions, right after casting and until ...

Pergamon-Elsevier Science Ltd2019

Micro-chemo-mechanical features of ultra-high performance glass concrete (UHPGC)

William Wilson, Luca Sorelli

The development of Ultra-High Performance Concrete (UHPC) opened new research directions for enhancing the architectural design, sustainability and serviceability of concrete structures. However, the costs and resource intensiveness trigger the need for in ...

ELSEVIER2019

Local tuning of fused silica thermal expansion coefficient using femtosecond laser

Yves Bellouard, Pieter Vlugter, Erica Kathleen Block

Femtosecond laser exposure of fused silica in the nonablative regime can lead to various localized bulk modifications of the material structure. In this paper, we show that these laser-induced modifications can be used to tune silica thermal expansion prop ...

2019

Concrete Performance of Limestone Calcined Clay Cement (LC3) Compared with Conventional Cements

Karen Scrivener, Lionel Sofia, François Henri Avet

This study aims to demonstrate the robustness of concrete made of limestone calcined clay cement (LC3). Two campaigns were carried out using 375 kg.m(-3) and 500 kg.m(-3) of binder and targeting plastic and self-placing workability, respectively. The concr ...

AMER SOC TESTING MATERIALS2019

Effect of replacement of silica fume with calcined clay on the hydration and microstructural development of eco-UHPFRC

Karen Scrivener, Mohammadhadi Kazemi Kamyab, Wei Sun, Wei Huang

In this paper, the replacement of high cost silica fume with calcined clay was investigated in UHPFRC mixes. The impact of two grades of calcined clay on the hydration and microstructural development of UHPFRC matrices was investigated, where 54% of the ce ...

Elsevier Sci Ltd2017

Page 2 of 2