A20 lineThe A20, or address line 20, is one of the electrical lines that make up the system bus of an x86-based computer system. The A20 line in particular is used to transmit the 21st bit on the address bus. A microprocessor typically has a number of address lines equal to the base-two logarithm of the number of words in its physical address space. For example, a processor with 4 GB of byte-addressable physical space requires 32 lines (log2(4 GB) = log2(232 B) = 32), which are named A0 through A31.
X86 instruction listingsThe x86 instruction set refers to the set of instructions that x86-compatible microprocessors support. The instructions are usually part of an executable program, often stored as a and executed on the processor. The x86 instruction set has been extended several times, introducing wider registers and datatypes as well as new functionality. x86 assembly language Below is the full 8086/8088 instruction set of Intel (81 instructions total). Most if not all of these instructions are available in 32-bit mode; they just operate on 32-bit registers (eax, ebx, etc.
X86 virtualizationx86 virtualization is the use of hardware-assisted virtualization capabilities on an x86/x86-64 CPU. In the late 1990s x86 virtualization was achieved by complex software techniques, necessary to compensate for the processor's lack of hardware-assisted virtualization capabilities while attaining reasonable performance. In 2005 and 2006, both Intel (VT-x) and AMD (AMD-V) introduced limited hardware virtualization support that allowed simpler virtualization software but offered very few speed benefits.
Real modeReal mode, also called real address mode, is an operating mode of all x86-compatible CPUs. The mode gets its name from the fact that addresses in real mode always correspond to real locations in memory. Real mode is characterized by a 20-bit segmented memory address space (giving 1 MB of addressable memory) and unlimited direct software access to all addressable memory, I/O addresses and peripheral hardware. Real mode provides no support for memory protection, multitasking, or code privilege levels.
General protection faultA general protection fault (GPF) in the x86 instruction set architectures (ISAs) is a fault (a type of interrupt) initiated by ISA-defined protection mechanisms in response to an access violation caused by some running code, either in the kernel or a user program. The mechanism is first described in Intel manuals and datasheets for the Intel 80286 CPU, which was introduced in 1983; it is also described in section 9.8.13 in the Intel 80386 programmer's reference manual from 1986.
Control registerA control register is a processor register that changes or controls the general behavior of a CPU or other digital device. Common tasks performed by control registers include interrupt control, switching the addressing mode, paging control, and coprocessor control. When IBM developed a paging version of the System/360, they added 16 control registers to the design for what became the 360/67. IBM did not provide control registers on other S/360 models, but made them a standard part of System/370, although with different register and bit assignments.
Protection ringIn computer science, hierarchical protection domains, often called protection rings, are mechanisms to protect data and functionality from faults (by improving fault tolerance) and malicious behavior (by providing computer security). Computer operating systems provide different levels of access to resources. A protection ring is one of two or more hierarchical levels or layers of privilege within the architecture of a computer system. This is generally hardware-enforced by some CPU architectures that provide different CPU modes at the hardware or microcode level.
Protected modeIn computing, protected mode, also called protected virtual address mode, is an operational mode of x86-compatible central processing units (CPUs). It allows system software to use features such as segmentation, virtual memory, paging and safe multi-tasking designed to increase an operating system's control over application software. When a processor that supports x86 protected mode is powered on, it begins executing instructions in real mode, in order to maintain backward compatibility with earlier x86 processors.
MS-DOSMS-DOS (ˌɛmˌɛsˈdɒs ; acronym for Microsoft Disk Operating System, also known as Microsoft DOS) is an operating system for x86-based personal computers mostly developed by Microsoft. Collectively, MS-DOS, its rebranding as IBM PC DOS, and a few operating systems attempting to be compatible with MS-DOS, are sometimes referred to as "DOS" (which is also the generic acronym for disk operating system).
Long modeIn the x86-64 computer architecture, long mode is the mode where a 64-bit operating system can access 64-bit instructions and registers. 64-bit programs are run in a sub-mode called 64-bit mode, while 32-bit programs and 16-bit protected mode programs are executed in a sub-mode called compatibility mode. Real mode or virtual 8086 mode programs cannot be natively run in long mode. An x86-64 processor acts identically to an IA-32 processor when running in real mode or protected mode, which are supported modes when the processor is not in long mode.
Preemption (computing)In computing, preemption is the act of temporarily interrupting an executing task, with the intention of resuming it at a later time. This interrupt is done by an external scheduler with no assistance or cooperation from the task. This preemptive scheduler usually runs in the most privileged protection ring, meaning that interruption and then resumption are considered highly secure actions. Such changes to the currently executing task of a processor are known as context switching.
X86 assembly languagex86 assembly language is the name for the family of assembly languages which provide some level of backward compatibility with CPUs back to the Intel 8008 microprocessor, which was launched in April 1972. It is used to produce object code for the x86 class of processors. Regarded as a programming language, assembly is machine-specific and low-level. Like all assembly languages, x86 assembly uses mnemonics to represent fundamental CPU instructions, or machine code.
P6 (microarchitecture)The P6 microarchitecture is the sixth-generation Intel x86 microarchitecture, implemented by the Pentium Pro microprocessor that was introduced in November 1995. It is frequently referred to as i686. It was planned to be succeeded by the NetBurst microarchitecture used by the Pentium 4 in 2000, but was revived for the Pentium M line of microprocessors. The successor to the Pentium M variant of the P6 microarchitecture is the Core microarchitecture which in turn is also derived from P6.
Task state segmentThe task state segment (TSS) is a structure on x86-based computers which holds information about a task. It is used by the operating system kernel for task management. Specifically, the following information is stored in the TSS: Processor register state I/O port permissions Inner-level stack pointers Previous TSS link All this information should be stored at specific locations within the TSS as specified in the IA-32 manuals. The TSS may reside anywhere in memory.
VMwareVMware, Inc. is an American cloud computing and virtualization technology company with headquarters in Palo Alto, California. VMware was the first commercially successful company to virtualize the x86 architecture. VMware's desktop software runs on Microsoft Windows, Linux, and macOS. VMware ESXi, its enterprise software hypervisor, is an operating system that runs on server hardware. In May 2022, Broadcom Inc. announced an agreement to acquire VMware in a cash-and-stock transaction valued at $61 billion.
