Publication

Shear strength of RC slabs under concentrated loads near clamped linear supports

Aurelio Muttoni, Miguel Fernández Ruiz, Francisco Manuel Maciel Natário
2014
Journal Articles

Abstract

Reinforced concrete slabs without shear reinforcement subjected to concentrated loads near linear sup- ports are usually designed or assessed in shear using design provisions that have been calibrated on the basis of tests on one-way slabs or beams with rectangular cross-section (slabs loaded over their full width). This approach may however be inconsistent, as the actual behavior of slabs under concentrated loads reflects a two-way slab response, with the shear forces not developing in a parallel manner in the failure region and with potential redistribution of the internal forces for increasing levels of load. In this research, a series of 12 tests on 6 full scale slabs (3.00 m 3.00 m 0.18 m) is presented. The slabs were centrally supported on an aluminum profile and were subjected to two concentrated symmet- rical loads. The support profile was equipped with vertical strain gauges, allowing to trace the distribu- tion of reactions at the supported line and its redistributions as the value of the concentrated loads increased. Significant redistributions of the reactions were actually measured prior to failure, which are presented and discussed within the paper. The aim of these measurements was to improve the under- standing of the mechanical behavior of such members and the role of shear cracking on the distribution of internal forces. A number of parameters was investigated, such as the location of the concentrated loads and the presence of ducts in the slab. This latter case (typical of prestressed concrete balanced cantilever bridges and residential buildings) has not been investigated in the past, despite its potential influence on the shear strength. The performance of these specimens is finally investigated and compared to the prediction of the fib - Model Code 2010 and the Critical Shear Crack Theory. This analysis shows that accurate predictions of the strength can be obtained if the influence of direct load strutting (for loads acting near supports) and redistribution of internal forces is accounted.

Official source

Aurelio Muttoni, Miguel Fernández Ruiz, Francisco Manuel Maciel Natário
2014
Journal Articles

Abstract

Official source

Related concepts (22)

Reinforced concrete

Reinforced concrete, also called ferroconcrete, is a composite material in which concrete's relatively low tensile strength and ductility are compensated for by the inclusion of reinforcement having higher tensile strength or ductility. The reinforcement is usually, though not necessarily, steel bars (rebar) and is usually embedded passively in the concrete before the concrete sets. However, post-tensioning is also employed as a technique to reinforce the concrete. In terms of volume used annually, it is one of the most common engineering materials.

Concrete slab

A concrete slab is a common structural element of modern buildings, consisting of a flat, horizontal surface made of cast concrete. Steel-reinforced slabs, typically between 100 and 500 mm thick, are most often used to construct floors and ceilings, while thinner mud slabs may be used for exterior paving . In many domestic and industrial buildings, a thick concrete slab supported on foundations or directly on the subsoil, is used to construct the ground floor. These slabs are generally classified as ground-bearing or suspended.

Prestressed concrete

Prestressed concrete is a form of concrete used in construction. It is substantially "prestressed" (compressed) during production, in a manner that strengthens it against tensile forces which will exist when in service. This compression is produced by the tensioning of high-strength "tendons" located within or adjacent to the concrete and is done to improve the performance of the concrete in service. Tendons may consist of single wires, multi-wire strands or threaded bars that are most commonly made from high-tensile steels, carbon fiber or aramid fiber.

Related publications (29)

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Marko Pejatovic

Codes of practice can be overly conservative, particularly for the shear resistance of reinforced concrete beams with shear reinforcement when large loads act close to supports. This thesis addresses the topic by proposing a refined design approach based o ...

EPFL2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024