Publications related to Probing the buckling of pressurized spherical shells

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Insights from an extensive triaxial testing campaign on a shale for comparative site characterization of a deep geological repository

Lyesse Laloui, Alessio Ferrari, Eleonora Crisci

Several boreholes were drilled for site comparison of a deep geological repository (DGR) in Northern Switzerland. The main target of the exploration program was the >100m thick Opalinus Clay, the designated host rock encountered at approximately 450 to 100 ...

Elsevier2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Instabilities in Elastic and Magneto-Elastic Beams and Shells: from Shell Buckling to the Design of a Programmable Braille Reader

Arefeh Abbasi

In this thesis, we conduct a comprehensive investigation into structural instabilities of both elastic and magneto-elastic beams and shells, resulting in a creative proposal to design a programmable braille reader. Methodologically, we combine numerical si ...

EPFL2024

Strain Gradients and Magnetoresistance in Microstructured 3D Topological Semi-metals

Jonas De Jesus Diaz Gomez

Three-dimensional topological semimetals have emerged as strong candidates to probe new fundamental physical phenomena that could be exploited to develop next generation electronics. However, many aspects of their electronic properties remain unclear. Thi ...

EPFL2023

Atomic-scale Characterization of Strain and Gate effects on Two-dimensional Materials by Scanning Tunneling Microscopy

Jz -Yuan Juo

Strain is an inevitable phenomenon in two-dimensional (2D) material, regardless of whether the film is suspended or supported. Moreover, strain is known to alter the physical and chemical properties, such as the band gap, charge carrier effective masses, d ...

EPFL2023

Deformation response of highly stretchable and ductile graphene kirigami under uniaxial and biaxial tension

Ye Wei, Yao Chen, Tong Guo

Kirigami, the ancient technique of paper cutting, has been successfully applied to enhance the stretchability and ductility of nanoscale graphene. However, existing experimentally realized graphene kirigami (GK) are created by introducing parallel cuts, ex ...

Amer Physical Soc2023

On the slip burst amplitude cutoff in dislocation-rich microcrystals

Andreas Mortensen, Luciano Borasi

The plastic deformation of small-scale face-centered cubic metals exhibits intermittent slip burst events that appear on stress-strain curves as sudden strain jumps and/or load drops. These events are generally attributed to the avalanche-like cooperative ...

Pergamon-Elsevier Science Ltd2023

Lattice Green's function method for Atomistic/Continuum coupling

Ankit Gupta

Metal plasticity is an inherently multiscale phenomenon due to the complex long-range field of atomistic dislocations that are the primary mechanism for plastic deformation in metals. Atomistic/Continuum (A/C) coupling methods are computationally efficient ...

EPFL2023

Geometric tolerances of welded connections with inelastic panel zones

Dimitrios Lignos, Andronikos Skiadopoulos, Ce Wen

Prequalified beam-to-column connections in steel moment resisting frames usually concentrate inelastic deformations in the steel beam ends. As such, nonlinear geo-metric instabilities (i.e., local buckling) may occur in these regions at modest lateral drif ...

Ernst & Sohn2023

Mechanics of Physical Knots: From Filaments in Contact to Surgical Suturing

Paul Johanns

In this thesis, we study the mechanics of tight physical knots. Knots are omnipresent in surgery, climbing, and sailing, with disastrous consequences when the filament or the rope fails to perform its function. Even if the importance of mechanical analysis ...

EPFL2023

Room-temperature strength of the interfacial bond between silica inclusions and iron

Andreas Mortensen, Alejandra Inés Slagter, David Hernandez Escobar, Sergio Perosanz Amarillo

The strength of the interface between iron (Fe) and individual spherical silica (SiO2) inclusions of 5 +/- 1 mu m diameter is measured by means of in-situ micro-cantilever bending tests conducted under displacement control within a scanning electron micros ...

Pergamon-Elsevier Science Ltd2023

Microscopic Digital Image Correlation Analysis of Strain Distributions in Stainless Steel 316L Induced by Multiaxial Cyclic Loading

Elif Cansu Kursun

Fatigue damage in materials results in localized strain at the microstructural level. In many engineering components of the cooling circuits of nuclear power plants, where austenitic steels are used, the material experiences multiaxial cyclic loading, eith ...

EPFL2023

A reduced-order, rotation-based model for thin hard-magnetic plates

Pedro Miguel Nunes Pereira de Almeida Reis, Dong Yan, Bastien Freddy Gustave Aymon

We develop a reduced-order model for thin plates made of hard magnetorheological elastomers (hard-MREs), which are composed of hard-magnetic particles embedded in a polymeric matrix. First, we propose a new magnetic potential, as an alternative to an exist ...

PERGAMON-ELSEVIER SCIENCE LTD2023

C-shells: Deployable Gridshells with Curved Beams

Mark Pauly, Francis Julian Panetta, Yingying Ren, Quentin Christian Becker, Davide Pellis, Seiichi Eduardo Suzuki Erazo

We introduce a computational pipeline for simulating and designing C-shells, a new class of planar-to-spatial deployable linkage structures. A C-shell is composed of curved flexible beams connected at rotational joints that can be assembled in a stress-fre ...

2023

Microstructure et usinabilité d'alliages de titane béta-métastable

Loïc Favre

Titanium has become in recent years an interesting material in many applications that require a combination of high mechanical properties and low density. It has the peculiarity of undergoing an allotropic transformation at 882°C. Below this temperature, ...

EPFL2023

Experimental investigation of rotational behavior of pseudo-ductile adhesive angle joints exhibiting variable strain rate

Thomas Keller, Abdolvahid Movahedirad, Ghazaleh Eslami

Pseudo-ductile behavior in composite structural frames can be achieved by enabling their beam-column joints to exhibit nonlinear structural response due to progressive damage, by using pseudo-ductile adhesives. This study investigates the static behavior o ...

2023

Laser powder bed fusion of Fe-based shape memory alloys for novel structural metamaterials and "smart" structures

Irene Ferretto

Laser powder bed fusion (LPBF) is a powder-based additive manufacturing (AM) technique, which shows great potential in the production of complex-shaped parts with unprecedented design freedom. In addition, it allows for an active manipulation of the micros ...

EPFL2023

Bounding the localized to ductile transition in porous rocks: implications for geo-reservoirs

Marie Estelle Solange Violay, Gabriel Gérard Dominique Meyer

Porous rocks have long been the focus of intense research driven by their importance in our society as host to our most essential resources (oil, gas, water, geothermal energy, etc), yet their rheology remains poorly understood. With increasing depth, poro ...

2023

The new Chapter 9 of Eurocode 8 Part 3 for Seismic Assessment of Existing Steel Structures

Dimitrios Lignos

The seismic assessment of existing steel structures necessitates the development of practice- oriented engineering models for use in nonlinear static and dynamic analysis procedures. These models should encompass the full range of the anticipated nonlinear ...

2023