Publications related to CRACK SHIELDING MECHANISMS OF INTERLAYERED EPOXY MATERIALS UNDER QUASI-STATIC AND FATIGUE LOADING

Two-dimensional quasi-static delamination in composite laminates under Mode-I and Mode-II conditions

Fiber-polymer composites consist of a polymer matrix and reinforcing fibers made of various materials. These composites exhibit exceptional properties, such as a high strength-to-weight ratio and excellent corrosion resistance, which has led to their incre ...

EPFL2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

An adaptive phase field approach to 3D internal crack growth in rocks

Tao Xu, Michael Heap, Alexandra Roma Larisa Kushnir

Modeling the 3D internal crack under compression entails complex fracture mechanics (mode I-II-III fracture), resulting in substantial computational costs and challenges in characterizing fracture morphology characterization for Phase Field Method (PFM) si ...

2024

Numerical investigation of two-dimensional Mode-II delamination in composite laminates

Thomas Keller, Anastasios Vassilopoulos, Congzhe Wang

Existing standards for delamination tests on composite materials typically employ one-dimensional (1D) beam specimens. However, such specimens may not represent real delamination scenarios in composite structures, where cracks tend to propagate in two dime ...

Elsevier Sci Ltd2024

Enabling simultaneous reprocessability and fire protection via incorporation of phosphine oxide monomer in epoxy vitrimer

Véronique Michaud, Valentin Rougier

The conception of epoxy thermosets with both reprocessability and flame retardancy delineates a new horizon in polymer science, offering a material solution that is not only superior in fire safety but is also environment friendly. Herein, a flame-retardan ...

Journal Mater Sci Technol2024

Influence of fiber orientation on the tensile behavior of UHPFRC and reinforced UHPFRC under static and fatigue loadings

Jian Zhan

Ultra-high performance fiber reinforced cementitious composite (UHPFRC) is a modern class of cementitious building materials. Because of its superior mechanical properties and durability, it is increasingly used globally to rehabilitate, strengthen and mod ...

EPFL2024

Self-catalysed frontal polymerisation enables fast and low-energy processing of fibre reinforced polymer composites

Véronique Michaud, Baris Çaglar, Jacobus Gerardus Rudolph Staal

Frontal polymerisation has the potential to bring unprecedented reductions in energy demand and process time to produce fibre reinforced polymer composites. Production of epoxy-based fibre reinforced polymer parts with high fibre volume content, commonly e ...

2024

Encapsulation strategies for mechanical impact and damp heat reliability improvement of lightweight photovoltaic modules towards vehicle-integrated applications

Fabiana Lisco

Lightweight modules are essential for next-generation vehicle-integrated photovoltaic (VIPV) applications, such as solar-powered cars, allowing integration of solar cells beyond the roof, and on the hood, boot and body panels, and thereby extending the dri ...

Elsevier2024

Functionalized Å-scale Pores in Graphene for Carbon Capture

Kuang-Jung Hsu

Single-layer graphene, hosting a high density of functionalized molecular-sieving atom-thick pores, is considered to be an excellent material for gas separation membranes. These functionalized atom-thick pores enable the shortest transport pathway across t ...

EPFL2024

Multi-scale characterization and modeling of notched strength and translaminar fracture in hybrid thin-ply composites based on different carbon fiber grades

Guillaume Clément Broggi

Owing to their high specific stiffness and strength, Carbon Fiber Reinforced Composites (CFRP) are ideal candidates for the development of lightweight high-performance structures. Within this family, thin-ply composites allow for wider design freedom and p ...

EPFL2023

Fatigue behavior and life prediction of wind turbine blade composite materials

Anastasios Vassilopoulos

Fatigue life prediction of wind turbine rotor blades is a very challenging task, as their failure is led by different failure types that act synergistically. Inherent defects like wrinkles, fiber misalignments, and voids that can be introduced during fabri ...

Woodhead Publishing (Elsevier)2023

Reliability analysis and partial safety format calibration considering the characteristics of the resistance of reinforced concrete structures

Qianhui Yu

Every engineering calculation is an approximation of reality, with inevitable uncertainties involved. This fact implies that a reliability verification accounting for the uncertainties is a necessary step in the design and assessment of structures. Nowaday ...

EPFL2023

Process development of pre-impregnated hybrid thin-ply composites

Alexios Argyropoulos

Thin-ply composites, obtained with recently developed fiber spreading techniques, rapidly gained industrial interest because they offer a large composite design freedom, and lead to a composite tensile strength that is close to that of the individual fiber ...

EPFL2023

Novel multi-crack damage approach for pultruded fiber-polymer web-flange junctions

Thomas Keller

This paper aims to propose a novel approach to assess the multi-crack behavior of layered fiber-polymer composites. The Compliance and R-curves generated from this novel approach were useful to understand the multiple delamination process, enabling to eval ...

Elsevier Sci Ltd2023

Effect of fiber architecture on tension-tension fatigue behavior of bolted basalt composite joints

Thomas Keller, Lulu Liu, Xin Wang

The effect of fiber architecture, i.e., unidirectional (UD) vs. multi-directional (MD), on the tension-tension fa-tigue behavior of bolted double-lap basalt composite joints was experimentally investigated. The fatigue load-life (F -N) curves of MD and UD ...

ELSEVIER SCI LTD2023

Energy dissipation in fiber-polymer composites adhesive joints under cyclic loading

Ghazaleh Eslami

Sustainable development has emerged as a paramount consideration in various fields of industry, including construction, to preserve the environment and its finite resources. Lightweight structures, such as fiber-polymer composite structures, address both s ...

EPFL2023

Three-dimensional hydraulic fracture propagation in homogeneous and heterogeneous media

Carlo Peruzzo

Hydraulic fractures are tensile fractures that occur in solid materials due to the natural intrusion or anthropogenic injection of a viscous fluid into a fracture channel. The deliberate creation of hydraulic fractures is part of an industrial technology h ...

EPFL2023

Incorporation of Lignin in Bio-Based Resins for Potential Application in Fiber-Polymer Composites

Mário Alexandre De Jesus Garrido, Mateus De Assunção Hofmann

Bio-based resins, obtained from renewable raw materials, are a more sustainable alternative to oil-based resins for fiber-reinforced polymer (FRP) composites. The incorporation of lignin in those resins has the potential to enhance their performance. This ...

MDPI2023

Visualization and modelling of dynamic flow in fibrous preforms for liquid composite molding

Helena Luisa Teixido Pedarros

Nowadays, Liquid Composite Molding techniques are often used to manufacture high quality fiber reinforced composite parts at a relatively low cost. These involve an infiltration process, in which a liquid resin is forced to ingress into a dry fibrous porou ...

EPFL2023