Publication

Externally Pressurised and Hybrid Bearings Lubricated with R134A for Oil- Free Compressors

Adam Molyneaux
1996
Conference Papers

Abstract

This paper discusses the choice and implementation of bearings for oil-free compressors where the system refrigerant is used as the lubricant in externally pressurised and hybrid bearings. The problems of oil contamination in heat pump application is described followed by methods to produce genuine oil-free hermetic systems. Alternative bearing choices are described for high and low speed applications. Theoretical and experimental results are presented showing the effects of turbulence in the bearing clearence and pockets of externally pressurised thrust and journal bearings for a co-rotating scroll compressor operating with r134a. The paper concludes that design methods are now available to enable the incorporation refrigerant lubricated bearing in hermetic oil-free compressors.

Official source

https://infoscience.epfl.ch/entities/publication/5a050d09-d201-463c-a56a-1b7ef38c8527

About this result

This page is automatically generated and may contain information that is not correct, complete, up-to-date, or relevant to your search query. The same applies to every other page on this website. Please make sure to verify the information with EPFL's official sources.

Adam Molyneaux
1996
Conference Papers

Abstract

Official source

https://infoscience.epfl.ch/entities/publication/5a050d09-d201-463c-a56a-1b7ef38c8527

About this result

Related concepts (19)

Compressor

A compressor is a mechanical device that increases the pressure of a gas by reducing its volume. An air compressor is a specific type of gas compressor. Compressors are similar to pumps: both increase the pressure on a fluid and both can transport the fluid through a pipe. The main distinction is that the focus of a compressor is to change the density or volume of the fluid, which is mostly only achievable on gases. Gases are compressible, while liquids are relatively incompressible, so compressors are rarely used for liquids.

Vapor-compression refrigeration

Vapour-compression refrigeration or vapor-compression refrigeration system (VCRS), in which the refrigerant undergoes phase changes, is one of the many refrigeration cycles and is the most widely used method for air conditioning of buildings and automobiles. It is also used in domestic and commercial refrigerators, large-scale warehouses for chilled or frozen storage of foods and meats, refrigerated trucks and railroad cars, and a host of other commercial and industrial services.

Fluid bearing

Fluid bearings are bearings in which the load is supported by a thin layer of rapidly moving pressurized liquid or gas between the bearing surfaces. Since there is no contact between the moving parts, there is no sliding friction, allowing fluid bearings to have lower friction, wear and vibration than many other types of bearings. Thus, it is possible for some fluid bearings to have near-zero wear if operated correctly. They can be broadly classified into two types: fluid dynamic bearings (also known as hydrodynamic bearings) and hydrostatic bearings.

Related publications (25)

Parametric Reduced Order Model of a Gas Bearings Supported Rotor

Jürg Alexander Schiffmann, Fabio Nobile, Dimitri Maurice Goutaudier

Gas bearings use pressurized gas as a lubricant to support and guide rotating machinery. These bearings have a number of advantages over traditional lubricated bearings, including higher efficiency in a variety of applications and reduced maintenance requi ...

2023

RE:SLAB — a load bearing system for open-ended component reuse in building structures

Dario Redaelli, Corentin Jean Dominique Fivet, Jan Friedrich Georg Brütting, Alex-Manuel Muresan, Edisson Xavier Estrella Arcos

The construction industry plays a major role in the high levels of greenhouse gas emissions, resource consumption, and waste generation observed nowadays. Key to the circular economy, structural component reuse arises as a promising solution to divert cons ...

2024

Design and assessment of an evaporating water-cooled methanation reactor for a SOE-based power-to-methane system

Philippe Aubin

The transition towards clean renewable energy sources, where wind and solar are prone to variation, requires adequate energy storage. Power-to-methane (PtM) systems can be part of the solution. Specifically, solid-oxide-electrolyser (SOE) based PtM systems ...

EPFL2024