Publication

Experimental investigation of multi-span post-tensioned glass beams

Alain Nussbaumer, Pieter Christian Louter, Jagoda Cupac
2017
Journal Articles

Abstract

This paper presents a study on post-tensioned glass beams in a statically indeterminate system. In order to increase the safety of structural glass beams, ductile reinforcement can be added to glass beam sections providing secondary load carrying mechanism in case of glass breakage. In the here investigated post-tensioned system, the reinforcement tendons are additionally pre-tensioned, introducing compressive pre-stress in the beam in order to increase the apparent tensile strength of glass. The system is tested in five-point bending at 23°C and 60°C in order to investigate the basic structural performance and the influence of temperature increase on the initial cracking load and the behaviour of the cracked beam. The efficiency of the applied system is compared to a reinforced beam system produced in the same batch with similar overall dimensions. The results show an increase of initial cracking load of the post-tensioned beams due to the applied pre-stress and a ductile post-cracking response, reaching high ultimate loads prior to failure.

Official source

https://infoscience.epfl.ch/entities/publication/6a4c573d-5c1e-4e31-9b9e-69b0d69c680b

About this result

This page is automatically generated and may contain information that is not correct, complete, up-to-date, or relevant to your search query. The same applies to every other page on this website. Please make sure to verify the information with EPFL's official sources.

Alain Nussbaumer, Pieter Christian Louter, Jagoda Cupac
2017
Journal Articles

Abstract

Official source

https://infoscience.epfl.ch/entities/publication/6a4c573d-5c1e-4e31-9b9e-69b0d69c680b

About this result

Related concepts (24)

Prestressed concrete

Prestressed concrete is a form of concrete used in construction. It is substantially "prestressed" (compressed) during production, in a manner that strengthens it against tensile forces which will exist when in service. This compression is produced by the tensioning of high-strength "tendons" located within or adjacent to the concrete and is done to improve the performance of the concrete in service. Tendons may consist of single wires, multi-wire strands or threaded bars that are most commonly made from high-tensile steels, carbon fiber or aramid fiber.

Reinforced concrete

Reinforced concrete, also called ferroconcrete, is a composite material in which concrete's relatively low tensile strength and ductility are compensated for by the inclusion of reinforcement having higher tensile strength or ductility. The reinforcement is usually, though not necessarily, steel bars (rebar) and is usually embedded passively in the concrete before the concrete sets. However, post-tensioning is also employed as a technique to reinforce the concrete. In terms of volume used annually, it is one of the most common engineering materials.

Beam (structure)

A beam is a structural element that primarily resists loads applied laterally to the beam's axis (an element designed to carry primarily axial load would be a strut or column). Its mode of deflection is primarily by bending. The loads applied to the beam result in reaction forces at the beam's support points. The total effect of all the forces acting on the beam is to produce shear forces and bending moments within the beams, that in turn induce internal stresses, strains and deflections of the beam.

Related publications (30)

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Experimental investigation of dowel action in reinforcing bars using refined measurements

Aurelio Muttoni, Marko Pejatovic

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

Ernst & Sohn2024