Publication

Analysis of the dynamic response of pump-turbine runners- Part I: Experiment

François Avellan, Mohamed Farhat, Xiaopeng Huang, Eduard Egusquiza
2012
Conference Papers

Abstract

When in operation, pump-turbine runners have to withstand large pressure pulsations generated by the rotor-stator interaction. The analysis of the dynamic behavior of these structures is necessary to avoid damage. For this analysis a realistic model of the runner is necessary. When the runner is submerged in water and inside the casing, its dynamic response is greatly affected. The added mass effects of the surrounding fluid and the proximity of the head-cover and bottom-cover may reduce the natural frequencies. The frequency reduction produced by the added mass effects and the influence of the boundary conditions has to be known for a safe design of the runner. In this paper an experimental investigation on the dynamic response of a model runner is presented. A reduced scale model of a pump-turbine was tested outside and inside the casing with different boundary conditions. For the excitation of the runner at different frequencies piezoelectric patches were used. The response was measured with miniature accelerometers located in several positions inside the runner. From the measurements the natural frequencies and mode-shapes of the runner were calculated using EMA. The influence of the added mass and of the boundary conditions is presented and discussed.

Official source

https://infoscience.epfl.ch/entities/publication/7e2f35b9-53cf-4bd8-9bb0-1647eb473286

About this result

This page is automatically generated and may contain information that is not correct, complete, up-to-date, or relevant to your search query. The same applies to every other page on this website. Please make sure to verify the information with EPFL's official sources.

François Avellan, Mohamed Farhat, Xiaopeng Huang, Eduard Egusquiza
2012
Conference Papers

Abstract

Official source

https://infoscience.epfl.ch/entities/publication/7e2f35b9-53cf-4bd8-9bb0-1647eb473286

About this result

Related concepts (31)

Water turbine

A water turbine is a rotary machine that converts kinetic energy and potential energy of water into mechanical work. Water turbines were developed in the 19th century and were widely used for industrial power prior to electrical grids. Now, they are mostly used for electric power generation. Water turbines are mostly found in dams to generate electric power from water potential energy. Water wheels have been used for hundreds of years for industrial power. Their main shortcoming is size, which limits the flow rate and head that can be harnessed.

Francis turbine

The Francis turbine is a type of water turbine. It is an inward-flow reaction turbine that combines radial and axial flow concepts. Francis turbines are the most common water turbine in use today, and can achieve over 95% efficiency. The process of arriving at the modern Francis runner design took from 1848 to approximately 1920. It became known as the Francis turbine around 1920, being named after British-American engineer James B. Francis who in 1848 created a new turbine design.

Pelton wheel

The Pelton wheel or Pelton Turbine is an impulse-type water turbine invented by American inventor Lester Allan Pelton in the 1870s. The Pelton wheel extracts energy from the impulse of moving water, as opposed to water's dead weight like the traditional overshot water wheel. Many earlier variations of impulse turbines existed, but they were less efficient than Pelton's design. Water leaving those wheels typically still had high speed, carrying away much of the dynamic energy brought to the wheels.

Related publications (27)

The Advection Boundary Law in presence of mean-flow and spinning modes

In the attempt to reduce fuel consumption, a new generation of Ultra-High-By-Pass-Ratio (UHBR) turbofans have been introduced in the aeronautic industry which are structurally noisier especially at lower frequencies, because of their larger diameter, lower ...

SPIE2024

An interior penalty coupling strategy for isogeometric non-conformal Kirchhoff-Love shell patches

Annalisa Buffa, Pablo Antolin Sanchez, Giuliano Guarino

This work focuses on the coupling of trimmed shell patches using Isogeometric Analysis, based on higher continuity splines that seamlessly meet the

C^1

requirement of Kirchhoff-Love-based discretizations. Weak enforcement of coupling conditions is achiev ...

Springer2024

Exponential convergence to steady-states for trajectories of a damped dynamical system modeling adhesive strings

Nicola De Nitti

We study the global well-posedness and asymptotic behavior for a semilinear damped wave equation with Neumann boundary conditions, modeling a one-dimensional linearly elastic body interacting with a rigid substrate through an adhesive material. The key fea ...

World Scientific Publ Co Pte Ltd2024