Thermodynamique chimique

Science de la nature
Chimie
Chimie physique
Thermodynamique chimique

À propos
Confidentialité
Mentions légales

Graph Chatbot

Publications associées (31)

Evaluation of the Effect of Backsheet Properties on PV Encapsulant Degradation under Ultraviolet-Damp-Heat Conditions

Djamel Eddine Mansour

The reliability of photovoltaic (PV) modules is highly determined by the durability of the polymeric components (backsheet and encapsulant). The power degradation and failure of PV modules can be caused by changes in the physical, chemical, and mechanical ...

EPFL2021

Characterization of untransformed ferrite in 10Cr and 12Cr ODS steels

Roland Logé

Two new ferrito-martensitic oxide dispersion strengthened (ODS) steels reinforced with (Y, Ti, O) nanoparticles were elaborated using a high-energy attritor. The milled powder was consolidated by hot extrusion at 1050 degrees C. The two types of ODS steels ...

ELSEVIER SCI LTD2021

Effects of Ball Milling and TiF3 Addition on the Dehydrogenation Temperature of Ca(BH4)2 Polymorphs

Andreas Züttel

The changes introduced by both ball milling and the addition of small amounts of TiF3 in the kinetics of the hydrogen desorption of three different Ca(BH4)2 polymorphs (α, β and γ) have been systematically investigated. The samples with different polymorph ...

2020

Structural and Dynamical Properties of Potassium Dodecahydro-monocarba-closo-dodecaborate: KCB11H12

Wei Zhou, Mirjana Dimitrievska

MCB11H12 (M: Li, Na) dodecahydro-monocarba-closo-dodecaborate salt compounds are known to have stellar superionic Li+ and Na+ conductivities in their high-temperature disordered phases, making them potentially appealing electrolytes in all-solid-state batt ...

AMER CHEMICAL SOC2020

Beam duct for the 1 MW neutral beam injector on TCV

Basil Duval, Yves Martin, Stefano Coda, Alexander Karpushov, Frédéric Dolizy, Matthieu Toussaint, Roberto Maurizio

The 1MW power of the neutral beam injector (NBI) enters the plasma of the Tokamak a Configuration Variable (TCV) through a duct. The original beam propagation model predicted a maximal heat flux on the internal faces of the duct below 350 kW/m(2), leading ...

2020

Evaporation of Metals during the Thermal Treatment of Oxide Nanomaterials in Cellulose-Based Matrices

Christian Ludwig, Mohamed Tarik

Like conventional material products, waste is the last stage of the life cycle of engineered nanomaterials, which are then incinerated or stabilized before disposal. However, because of their special physical characteristics, the fate of the thermally trea ...

2020

Reusability of filtering facepiece respirators after decontamination through drying and germicidal UV irradiation

David Vernez, Véronique Michaud, Guillaume Suarez, Kiattisak Batsungnoen

Introduction During pandemics, such as the SARS-CoV-2, filtering facepiece respirators plays an essential role in protecting healthcare personnel. The recycling of respirators is possible in case of critical shortage, but it raises the question of the effe ...

2020

Effect of temperature on the water content of C-A-S-H in plain Portland and blended cements

Karen Scrivener, François Henri Avet

This study aims to investigate the change with temperature of the water content of the C-(A)-S-H of plain cement (PC) and Limestone Calcined Clay Cement (LC3). The water content was determined by various methods: thermogravimetric analysis (TGA), H-1-nucle ...

Pergamon-Elsevier Science Ltd2020

Visualizing the importance of oxide-metal phase transitions in the production of synthesis gas over Ni catalysts

Stéphane François Jean Poitel

Synthesis gas, composed of H-2 and CO, is an important fuel which serves as feedstock for industrially relevant processes, such as methanol or ammonia synthesis. The efficiency of these reactions depends on the H-2 : CO ratio, which can be controlled by a ...

2020

Tethering (Arene)Ru(II) Acylpyrazolones Decorated with Long Aliphatic Chains to Polystyrene Surfaces Provides Potent Antibacterial Plastics

Paul Joseph Dyson

The acylpyrazolone proligands HQR (HQR in general, in detail: HQCy = 1-phenyl-3-methyl-4-carbonylcyclohexyl-5-pyrazolone, 4-C(O)-phenyl, HQPh = 1-phenyl-3-methyl-4-benzoyl-5-pyrazolone, HQC17 = 1-phenyl-3-methyl-4-stearoyl-5-pyrazolone, HQC17,Ph = 1-phenyl ...

2020

Influence of local fiber distribution on tensile behavior of strain hardening UHPFRC using NDT and DIC

Eugen Brühwiler, Xiujiang Shen

This paper introduces the uniformity factor mu(2) for considering the local fiber distribution within elements made with Ultra-High Performance Fiber Reinforced Cementitious Composites (UHPFRC). The influence of mu(2) on the strain-hardening response of UH ...

Pergamon-Elsevier Science Ltd2020

Page 2 sur 2