Publications associées à Cupronickel

Micro-addition of Fe in highly alloyed Cu-Ti alloys to improve both formability and strength

Roland Logé, Cyril Cayron, Baptiste Thomas Jean Rouxel

Cu-Be alloys provide excellent electrical and mechanical properties, but present serious health hazards during manufacturing. Among alternative alloys, the Cu-Ti system has the highest yield strength; however, Ti cannot be easily solutionized at concentrat ...

ELSEVIER SCI LTD2022

In situ growth of graphene on both sides of a Cu-Ni alloy electrode for perovskite solar cells with improved stability

Michael Graetzel, Yinghui Wu, Huimin Su

The instability of rear electrodes undermines the long-term operational durability of efficient perovskite solar cells. Here, a composite electrode of copper-nickel (Cu-Ni) alloy stabilized by in situ grown bifacial graphene is designed. The alloying makes ...

NATURE PORTFOLIO2022

A Study on the Characteristics of Cu-Mn-Dy Alloy Resistive Thin Films

Ho-Yun Lee

Cu-Mn-Dy resistive thin films were prepared on glass and Al2O3 substrates, which was achieved by co-sputtering the Cu-Mn alloy and dysprosium targets. The effects of the addition of dysprosium on the electrical properties and microstructures of annealed Cu ...

2019

Ductility reduction factor formulations for seismic design of RC wall and frame structures

Katrin Beyer, Matteo Zerbin

Seismic design of standard structures is typically founded on a force-based design approach. Over the years this approach has proven robust and easily applicable by design engineers and - in combination with capacity design principles - it provides a good ...

2019

Dislocation cross-slip in fcc solid solution alloys

William Curtin, Wolfram Georg Nöhring

Cross-slip is a fundamental process of screw dislocation motion and plays an important role in the evolution of work hardening and dislocation structuring in metals. Cross-slip has been widely studied in pure FCC metals but rarely in FCC solid solutions. H ...

2017

Influence of icosahedral short range order on diffusion in liquids: A study on Al-Zn-Cr alloys

Michel Rappaz, Güven Kurtuldu

It has been shown recently that minute additions of Cr in Al-Zn alloys refine the solidified grain structure and induce multiply-twinned grains which can only be explained if the icosahedral symmetry is considered (Kurtuldu et al., 2013). It has been sugge ...

Elsevier2016

Structural anelasticity, elasticity and broken ergodicity in Ni-Ti shape memory alloys

Daniele Mari

New data are presented on dynamic measurements of elasticity and anelasticity of several poly- and single crystalline Ni1+xTi1-x alloys for frequencies between 0.05 and 100 kHz over a wide temperature range below room temperature. Anelastic effects, previo ...

Pergamon-Elsevier Science Ltd2014

Dendritic Growth Morphologies in Al-Zn Alloys-Part I: X-ray Tomographic Microscopy

Michel Rappaz, Jonathan Friedli, Paolo Di Napoli

Upon solidification, most metallic alloys form dendritic structures that grow along directions corresponding to low index crystal axes, e.g., directions in fcc aluminum. However, recent findings[1,2] have shown that an increase in the zinc content in Al-Zn ...

Springer Verlag2013

Cu(In1-xGax)S-2 nanocrystals and films: low-temperature synthesis with size and composition control

Giorgio Margaritondo

We demonstrate a single-step X-ray irradiation process that yields high-quality Cu(In1-xGax)S-2 nanocrystals in colloidal solutions, with complete control of size and composition. Thin films produced by drop-casting exhibit high-quality photoresponse, conf ...

Royal Soc Chemistry2013

Material and velocity effects on cavitation erosion pitting

Ayat Karimi, Jean-Pierre Franc

Cavitation erosion during the incubation period was investigated via pitting tests conducted on three different materials: an Aluminum alloy, a Nickel Aluminum Bronze alloy and a Duplex Stainless Steel. Pitting tests were conducted in a cavitation tunnel i ...

2012

Application of spherical nanoindentation to determine the pressure of cavitation impacts from pitting tests

Ayat Karimi, Davide Carnelli, Jean-Pierre Franc

This article focuses on the use of spherical nanoindentation measurements to estimate the pressure of cavitation impacts and its statistical distribution. Indeed, nanoindentation techniques are supposed to represent an effective tool in this field due to t ...

Cambridge University Press2012

Scaling study of cavitation pitting from cavitating jets and ultrasonic horns

Ayat Karimi, Jean-Pierre Franc

Cavitation erosion prediction and characterization of cavitation field strength are of interest to industries suffering from cavitation erosion detrimental effects. One means to evaluate cavitation fields and materials is to examine pitting rates during th ...

Elsevier Science Sa2012

Intergranular penetration of liquid gold into stainless steel

Michel Rappaz, Léa Deillon, Jean-Daniel Wagnière, Denis Favez

Intergranular penetration of liquid 18 K gold into a superaustenitic stainless steel, which occurs during laser welding of these two materials, has been studied using a C-ring device which can be put under tensile stresses by a screw. It is shown that liqu ...

Elsevier2011

Phase Transformations in 18-Carat Gold Alloys Studied by Mechanical Spectroscopy

John Hennig

This work is motivated by an industrial interest in gaining a better understanding of the phase transformations that govern the mechanical properties of 18-carat gold alloys commonly used in jewelry applications and luxury watchmaking. These alloys fall in ...

EPFL2010

Soudage laser or-acier : métallurgie et procédé

Denis Favez

In jewelry manufacturing, joining dissimilar materials is usually achieved by brazing or soldering, in which the materials comprising the joint are heated to a suitable temperature in the presence of a filler metal having a liquidus below the solidus of th ...

EPFL2009

Microstructure and embrittlement of leaded copper alloys

Laurent Felberbaum

Mechanisms responsible for the embrittlement of leaded "free-machining" copper alloys at intermediate temperatures (i.e. around 400 °C) are examined using a combination of microstructural and mechanical characterization. Tensile tests are conducted on pure ...

EPFL2005