Publications associées à Armature (technique)

Contributions to rebar-to-concrete interaction and its structural implications for design and monitoring applications

Bond between reinforcing bars and concrete has been the focus of extensive research over the last century. This is well-justified as the functioning of reinforced concrete intimately depends on the interaction between rebar and concrete, as for example cra ...

EPFL2024

Additively manufactured steel reinforcement for small scale reinforced concrete modeling: Tensile and bond behavior

Christian Leinenbach, Rafal Wróbel

Small scale (1:30-1:40) Reinforced Concrete is useful for centrifuge testing. However, manufacturing the reinforcing cages by hand at this scale is practically difficult. This paper suggests that small scale reinforcement can be manufactured using a metal ...

Elsevier Sci Ltd2024

Estimation of the bar stress based on crack width measurements in reinforced concrete structures

Aurelio Muttoni, Enrique Corres Sojo

Estimating the stress of reinforcing bars and its variations in service conditions can be useful to determine the reserve capacity of structures or to assess the risk of fatigue in the reinforcement. This paper investigates the use crack width measurements ...

Ernst & Sohn2024

Experimental investigation of dowel action in reinforcing bars using refined measurements

Aurelio Muttoni, Marko Pejatovic

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

Ernst & Sohn2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Marko Pejatovic

Codes of practice can be overly conservative, particularly for the shear resistance of reinforced concrete beams with shear reinforcement when large loads act close to supports. This thesis addresses the topic by proposing a refined design approach based o ...

EPFL2024

Decarbonization potential of steel fibre-reinforced limestone calcined clay cement concrete one-way slabs

Hisham Tarek Mohamed Hafez

This study deals with a comparison of the environmental performance of one-way slabs utilizing steel fibrereinforced limestone calcined clay cement (LC3) concrete with the control case of Ordinary Portland cement concrete. The experimental program constitu ...

Elsevier Sci Ltd2024

Mesh-based topology, shape and sizing optimization of ribbed plates

In this paper, we present a new parameterization and optimization procedure for minimizing the weight of ribbed plates. The primary goal is to reduce embodied CO2 in concrete floors as part of the effort to diminish the carbon footprint of the construction ...

Springer2024

FLO:RE – A new floor system made of reused reinforced concrete and steel elements

Corentin Jean Dominique Fivet, Numa Joy Bertola, Maléna Bastien Masse, Célia Marine Küpfer

Carefully extracting reinforced concrete (RC) elements from soon-to-be demolished structures and reusing them as load-bearing components is an emerging circular low-carbon alternative to building new structures. As floor construction typically accounts for ...

IABSE2024

Structural component reuse of precast and cast-in-place reinforced concrete in architecture since the late 1960s in Europe

Corentin Jean Dominique Fivet, Célia Marine Küpfer

The reuse of concrete pieces salvaged from structures undergoing transformation or demolition into new architectural projects has gained a sudden and visible interest over the past five years. However, the practice of reusing concrete pieces in new structu ...

vdf Hochschulverlag AG2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Localized Ionic Reinforcement of Double Network Granular Hydrogels

Esther Amstad, Alexandra Thoma

Nature produces soft materials with fascinating combinations of mechanical properties. For example, the mussel byssus embodies a combination of stiffness and toughness, a feature that is unmatched by synthetic hydrogels. Key to enabling these excellent mec ...

Wiley-V C H Verlag Gmbh2024

A Discussion on the Reliability of prEN1992-1-1:2021 Shear Strength Provisions for Fibre Reinforced Concrete Members Without Shear Reinforcement

Miguel Fernández Ruiz

The Eurocode 2 for the design of concrete structures (EN1992-1-1:2004) is undergoing a revision that will lead to the publication of the second generation of this code to be used across all CEN member countries. Therefore, the impact of the code will reach ...

SPRINGER INTERNATIONAL PUBLISHING AG2023

Building structures made of reused cut reinforced concrete slabs and walls: A case study

Corentin Jean Dominique Fivet, Maléna Bastien Masse, Nicole Widmer

Reuse of reinforced concrete (RC) components reduces construction’s environmental impacts and waste. Rather than crushing the concrete of an obsolete structure, its components are saw cut and later reassembled in a new structure. The theoretical feasibilit ...

CRC Press2023

Proposed Limits of Stiffener Spacing Requirements for EBF Links Within the Framework of Eurocode 8

Dimitrios Lignos, Nikolaos Skretas

Design specifications for Eccentrically Braced Frames (EBFs) provided by both the current AISC and Eurocode (EC) 8 seismic provisions are primarily based on physical tests conducted in the early 1980s. The tests investigated the behavior of, mostly short, ...

EEME2023

Low-tech methods for the reuse of reinforced concrete structural elements

Corentin Jean Dominique Fivet, Maléna Bastien Masse, Nicole Widmer, Julie Rachel Devènes

Most of existing buildings are made of concrete, new buildings are being built with it and others are demolished when still in good structural condition. This drives increased demands for raw materials, greenhouse gas emissions, and an accumulation of demo ...

2023

Panorama of approaches to reuse concrete pieces: identification and critical comparison

Corentin Jean Dominique Fivet, Célia Marine Küpfer

Practices that reuse concrete pieces in new building or infrastructure projects are currently diversifying as concrete reuse gains more and more relevance for sustainability. The present research provides a yet missing identification of the main approaches ...

IOP Publishing2023

Design of New Low-Carbon Floor Systems by Reusing Cut Cast-in-Place Concrete Pieces

Corentin Jean Dominique Fivet, Numa Joy Bertola, Célia Marine Küpfer

As floors typically account for the largest share of a building embodied carbon footprint, new strategies to build low-carbon floors must be developed and implemented. Among these strategies, the reuse of existing components is a promising circular approac ...

Novus Press2023

Reinforcement bond performance in 3D concrete printing: Explainable ensemble learning augmented by deep generative adversarial networks

Xianlin Wang

Integrating various reinforcements into 3D concrete printing (3DCP) is an efficient method to satisfy critical requirements for structural applications. This paper explores an explainable ensemble machine learning (EML) method to predict the bond failure m ...

Elsevier2023

Experimental testing and structural analysis of composite tile – reinforced concrete domes

Savvas Saloustros

Conventional formworks for concrete curved shells either are expensive, complex and wasteful or have formal restrictions. Using tile vaults (also known as timbrel, Guastavino, thin-tile or Catalan vaults) as stay-in-place formwork for concrete shells could ...

2023