Publications associées à Enrobé

A concrete answer for circular construction: three prototypes reusing saw-cut elements

Corentin Jean Dominique Fivet, Maléna Bastien Masse, Célia Marine Küpfer

Existing concrete buildings should be retained for as long as possible to reduce the environmental burden of demolition and new construction. However, when urban pressure makes demolition unavoidable, salvaging and reusing concrete elements elsewhere in ne ...

2024

Additively manufactured steel reinforcement for small scale reinforced concrete modeling: Tensile and bond behavior

Christian Leinenbach, Rafal Wróbel

Small scale (1:30-1:40) Reinforced Concrete is useful for centrifuge testing. However, manufacturing the reinforcing cages by hand at this scale is practically difficult. This paper suggests that small scale reinforcement can be manufactured using a metal ...

Elsevier Sci Ltd2024

Decarbonization potential of steel fibre-reinforced limestone calcined clay cement concrete one-way slabs

Hisham Tarek Mohamed Hafez

This study deals with a comparison of the environmental performance of one-way slabs utilizing steel fibrereinforced limestone calcined clay cement (LC3) concrete with the control case of Ordinary Portland cement concrete. The experimental program constitu ...

Elsevier Sci Ltd2024

FLO:RE – A new floor system made of reused reinforced concrete and steel elements

Corentin Jean Dominique Fivet, Numa Joy Bertola, Maléna Bastien Masse, Célia Marine Küpfer

Carefully extracting reinforced concrete (RC) elements from soon-to-be demolished structures and reusing them as load-bearing components is an emerging circular low-carbon alternative to building new structures. As floor construction typically accounts for ...

IABSE2024

Reusability assessment of reinforced concrete components prior to deconstruction from obsolete buildings

Corentin Jean Dominique Fivet, Maléna Bastien Masse, Julie Rachel Devènes

A large part of building demolitions is motivated by purely socio-economic reasons. Hence, about-to-be-demolished structures, commonly made of reinforced concrete, very often present no or little degradation. When adaptive reuse of the entire building is n ...

2024

Experimental investigation of dowel action in reinforcing bars using refined measurements

Aurelio Muttoni, Marko Pejatovic

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

Ernst & Sohn2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Structural component reuse of precast and cast-in-place reinforced concrete in architecture since the late 1960s in Europe

Corentin Jean Dominique Fivet, Célia Marine Küpfer

The reuse of concrete pieces salvaged from structures undergoing transformation or demolition into new architectural projects has gained a sudden and visible interest over the past five years. However, the practice of reusing concrete pieces in new structu ...

vdf Hochschulverlag AG2024

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Marko Pejatovic

Codes of practice can be overly conservative, particularly for the shear resistance of reinforced concrete beams with shear reinforcement when large loads act close to supports. This thesis addresses the topic by proposing a refined design approach based o ...

EPFL2024

From concrete waste to walls: An investigation of reclamation and digital technologies for new load-bearing structures

Corentin Jean Dominique Fivet, Stefana Parascho, Maxence Grangeot

The research presented in this paper highlights current practices for the end-of-life of concrete and explores opportunities in using unaltered concrete rubbles from demolition for the digital construction of structural walls. Through research by iterative ...

2023

Reusability Assessment of Obsolete Reinforced Concrete Structural Components

Corentin Jean Dominique Fivet, Maléna Bastien Masse, Célia Marine Küpfer, Julie Rachel Devènes

The production of concrete, the most widely used construction material, detrimentally affects the environment. Obsolete reinforced concrete (RC) load-bearing structures, even when still in good condition, are today prematurely crushed and landfilled or rec ...

Springer2023

Does carbon footprint reduction impair mechanical properties and service life of concrete?

Karen Scrivener, Diana Londoño Zuluaga

The aim of this study is to evaluate how much the changes in the concrete mix design, which enable carbon footprint reduction, are impacting mechanical properties and predicted service life of concrete structure. The starting point of this study was concre ...

SPRINGER2023

Reuse of concrete components in new construction projects: Critical review of 77 circular precedents

Corentin Jean Dominique Fivet, Maléna Bastien Masse, Célia Marine Küpfer

Extracting pieces of concrete from obsolete buildings and reusing them, as is, in new assemblies is today rarely considered a strategy for improving the sustainability of the construction sector. By delaying the crushing of concrete into aggregates and avo ...

2023

Design of New Low-Carbon Floor Systems by Reusing Cut Cast-in-Place Concrete Pieces

Corentin Jean Dominique Fivet, Numa Joy Bertola, Célia Marine Küpfer

As floors typically account for the largest share of a building embodied carbon footprint, new strategies to build low-carbon floors must be developed and implemented. Among these strategies, the reuse of existing components is a promising circular approac ...

Novus Press2023

Data-driven optimization tool for the functional, economic, and environmental properties of blended cement concrete using supplementary cementitious materials

Hisham Tarek Mohamed Hafez

The need to produce more sustainable concrete is proving imminent given the rising environmental concerns facing the industry. Blended cement concrete, based on any of the prominent supplementary cementitious materials (SCMs) such as fly ash, ground granul ...

ELSEVIER2023

Low-tech methods for the reuse of reinforced concrete structural elements

Corentin Jean Dominique Fivet, Maléna Bastien Masse, Nicole Widmer, Julie Rachel Devènes

Most of existing buildings are made of concrete, new buildings are being built with it and others are demolished when still in good structural condition. This drives increased demands for raw materials, greenhouse gas emissions, and an accumulation of demo ...

2023

Environmental and economic analysis of new construction techniques reusing existing concrete elements: two case studies

Corentin Jean Dominique Fivet, Maléna Bastien Masse, Célia Marine Küpfer, Julie Rachel Devènes

As the most widely used construction material worldwide, concrete is the main cause of greenhouse gas emissions, material depletion, and waste generation by the construction industry. Typically, concrete waste is crushed and, at best, reclaimed into recycl ...

2022

Re:Crete – reuse of concrete elements in new structures: A footbridge prototype

Corentin Jean Dominique Fivet, Maléna Bastien Masse, Célia Marine Küpfer, Jan Friedrich Georg Brütting, Julie Rachel Devènes

Concrete accounts for the largest share of worldwide building material use and waste generation, with cement production being responsible for approximately 9% of global anthropogenic CO2 emissions. A currently untapped strategy to significantly reduce thes ...

CRC Press2022

Multi-recycling of polypropylene fibre reinforced concrete: Influence of recycled aggregate properties on new concrete

Hisham Tarek Mohamed Hafez

Herein, an investigation of multi-generational recyclability of polypropylene fibre reinforced concrete (PPFRC) was performed. The parent concretes were produced with 0 and 6 kg/m(3) of polypropylene fibres. After recycling, the obtained coarse recycled co ...

ELSEVIER SCI LTD2022

Validation of bond models for the crack width estimation based on detailed measurements

Aurelio Muttoni, Enrique Corres Sojo

Crack formation and development in reinforced concrete structures is a complex mechanism affected by a large number of factors. Typically, the estimation of the crack width as a function of the reinforce-ment stress state is based on simplified assumptions ...

2022