Publications de Pierluigi Bruzzone

Numerical Analysis of Non-Insulated DEMO TF Coils

Pierluigi Bruzzone, Kamil Sedlák, Nikolay Bykovskiy

The design of small solenoids without/with-partial insulation (PI) among turns or layers has been proven to grant higher thermal stability than for standard insulated cases. This technology also implies higher safety standards, by e.g. reducing the coil vo ...

IEEE Institute of Electrical and Electronics Engineers2025

DC and quench performance assessment from the EUROfusion HTS Quench Experiment campaign and projection to magnet operation

Pierluigi Bruzzone, Davide Uglietti, Kamil Sedlák, Nikolay Bykovskiy

Seven different high current conductors for fusion applications, made of High Temperature Superconducting stacked tapes, have been successfully tested in the Quench Experiment campaign supported by EUROfusion and carried out in SULTAN. The aim of this exte ...

2025

Conceptual Design of the EDIPO 2 Magnet

Pierluigi Bruzzone, Kamil Sedlák, Nikolay Bykovskiy

The SULTAN test facility has been pivotal in qualifying forced-flow conductors in the last three decades. However, the rising demand for conductors for high-field magnets calls for a test facility able to provide a background magnetic field beyond the 11 T ...

IEEE Institute of Electrical and Electronics Engineers2025

Performance Comparison of Cables With Partial Transposition

Pierluigi Bruzzone, Kamil Sedlák, Chiara Frittitta, Federica Demattè

The need of full transposition of the current carrying elements (strands) in large cables is frequently retained as top design criterion for conductors operating in pulsed mode. However, when the transposition error, i.e., the inductance difference among t ...

IEEE Institute of Electrical and Electronics Engineers2024

Performance test of REBCO CICC sub-cables with l0 kA current under 20 T background field

Pierluigi Bruzzone

Iop Publishing Ltd2024

Bending Tolerance of React&Wind Nb3Sn Conductors for Fusion Magnets

Pierluigi Bruzzone, Kamil Sedlák, Chiara Frittitta, Federica Demattè

The react-and-wind technique for manufacturing of large Nb3Sn fusion magnets (RW) is very attractive because of the superior performance of the Nb3Sn with lower thermal strain compared to the wind-and-react technique. The procedure for magnet winding is al ...

IEEE Institute of Electrical and Electronics Engineers2024

Manufacture and performance test result of a 95 kA-class Nb-Ti cable-in-conduit conductor for the low field winding-package of CFETR-TF coil

Pierluigi Bruzzone, Kamil Sedlák

The engineering design of the CFETR TF prototype coil and conductors has been completed. The wind-package (WP) of the coil is graded into three regions based on the magnetic field distribution for saving cost. High-Jc Nb3Sn strand, ITER-like Nb3Sn strand a ...

Elsevier2023

Studies on EU-DEMO 3D coils requirements and conceptual design for error field correction and plasma control

Pierluigi Bruzzone, Hartmut Zohm, Leonardo Pigatto

This work presents the initial studies on the requirements for the design of 3D coils on EU-DEMO. The use of 3D coils in present machines includes two main purposes: the first one is the Error Field Correction (EFC). The EFC aims at minimizing the intrinsi ...

Elsevier Science Sa2023

Progress in the design and manufacturing of the EDIPO 2 cryostat

Pierluigi Bruzzone, Kamil Sedlák, Roberto Guarino, Evgeny Solodko

A major upgrade of the European DIPOle (EDIPO) test facility, which will allow the testing of superconducting samples both for fusion and for high-energy physics applications, is taking place at the Swiss Plasma Center. With a target background field of 15 ...

2023

Parametric Studies of the EU DEMO Central Solenoid

Pierluigi Bruzzone, Kamil Sedlák

The Central Solenoid (CS) is at the core of the EU DEMO tokamak, and has a strong impact on the tokamak design and the overall machine size. By ramping its current, the CS generates a change of magnetic flux, which initiates the plasma, and induces and con ...

IEEE Institute of Electrical and Electronics Engineers2023

Experimental study of stability, quench propagation and detection methods on 15 kA sub-scale HTS fusion conductors in SULTAN

Pierluigi Bruzzone, Kamil Sedlák, Nikolay Bykovskiy, Ortensia Dicuonzo

High-temperature superconductors (HTSs) enable exclusive operating conditions for fusion magnets, boosting their performance up to 20 T generated magnetic fields in the temperature range from 4 K to 20 K. One of the main technological issues of HTS conduct ...

2023

Quench experiments on sub-size HTS Cable-In-Conduit Conductors for fusion applications: Data analysis and model validation

Pierluigi Bruzzone, Boris Stepanov, Kamil Sedlák, Ortensia Dicuonzo

The recent experimental campaign, carried out in the upgraded SULTAN facility and supported by EUROfusion, investigated quench propagation in high field, sub-size HTS Cable-In-Conduit Conductors. The available experimental data consist of voltage, jacket a ...

ELSEVIER SCI LTD2023

Preliminary Design of a High Current R&W TF Coil Conductor for the EU DEMO

Pierluigi Bruzzone, Kamil Sedlák, Federica Demattè

Paschen failures in ITER, W7-X and JT60 superconducting coils at the acceptance tests have shown that it is highly desirable to lower the coil discharge voltage (U-d) of the DEMO Toroidal Field (TF) coils. Another benefit of lowering the U-d might be the r ...

IEEE Institute of Electrical and Electronics Engineers2022

Measurements of AC Loss Evolution in ITER TF Conductors

Pierluigi Bruzzone, Kamil Sedlák

AC loss in the Nb3Sn cable-in-conduit conductors (CICC) usually decreases after the conductor undergoes electromagnetic cycling. This can be attributed to the increase of inter-strand resistance due to the detachment of the strand-bonding during cyclic loa ...

IEEE Institute of Electrical and Electronics Engineers2022

Diffusion-Bonding Between Strands and Modeling of Splices of Nb3Sn Rutherford Cables

Pierluigi Bruzzone, Kamil Sedlák, Nikolay Bykovskiy

Particle accelerators foresee the use of Nb3Sn in the next generation of dipole magnets. A common design strategy is to grade the coil, i.e., to optimize the quantity of superconductor in the turns with respect to the magnetic field intensity. As a consequ ...

IEEE Institute of Electrical and Electronics Engineers2022

Application of Copper Thermal Spraying for Electrical Joints between Superconducting Nb3Sn Cables

Pierluigi Bruzzone, Vincenzo D'Auria

This manuscript reports on the application of copper thermal spraying in the manufacturing process of an electrical connection between Nb3Sn cables for superconducting magnets of fusion reactors. The joint is realized through diffusion bonding of the spray ...

MDPI2022

Preliminary design of the pressure relief system of the EDIPO 2 helium vessel

Pierluigi Bruzzone, Kamil Sedlák, Roberto Guarino, Evgeny Solodko

The European Dipole (EDIPO) test facility is undergoing a major upgrade of its magnet assembly, which will provide ground for testing both fusion and high-energy physics superconducting samples at variable temperature and with a background field of 15 T. I ...

2022

Co-Wound Superconducting Wire for Quench Detection in Fusion Magnets

Pierluigi Bruzzone, Davide Uglietti, Kamil Sedlák, Nikolay Bykovskiy

High temperature superconducting (HTS) materials are widely utilized in various design proposals for fusion magnets, resulting in enhanced performance of the machines compared to the past. However, a reliable quench detection in HTS conductors remains an o ...

IEEE Institute of Electrical and Electronics Engineers2022

The DEMO magnet system - Status and future challenges

Rainer Wesche, Pierluigi Bruzzone, Davide Uglietti, Kamil Sedlák, Roberto Guarino, Mithlesh Kumar, Vincenzo D'Auria, Ortensia Dicuonzo, Chiara Frittitta, Federica Demattè

We present the pre-concept design of the European DEMO Magnet System, which has successfully passed the DEMO plant-level gate review in 2020. The main design input parameters originate from the so-called DEMO 2018 baseline, which was produced using the PRO ...

2022

Parametric study of the TF coil design for the European DEMO

Rainer Wesche, Pierluigi Bruzzone, Kamil Sedlák, Roberto Guarino

In addition to a reduced number of feeders, which would simplify their integration in the cryostat of the tokamak, the present study considers the possibility to reduce the voltage during safety discharge of the toroidal field (TF) coils. A lowered dischar ...

2021