Publications associées à Elevated temperature, micro-compression transient plasticity tests. on nanocrystalline Palladium-Gold: Probing activation parameters at the lower limit of crystallinity

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Strain engineering and strain measurement by spring tethers on suspended epitaxial GaN-on-Si photonic crystal devices

Romuald Houdré, Jun Wang

Suspended epitaxial gallium nitride (GaN) on silicon (Si) photonic crystal devices suffer from large residual tensile strain, especially for long waveguides, because fine structures tend to crack due to large stress. By introducing spring-like tethers, des ...

Iop Publishing Ltd2024

Insights from an extensive triaxial testing campaign on a shale for comparative site characterization of a deep geological repository

Lyesse Laloui, Alessio Ferrari, Eleonora Crisci

Several boreholes were drilled for site comparison of a deep geological repository (DGR) in Northern Switzerland. The main target of the exploration program was the >100m thick Opalinus Clay, the designated host rock encountered at approximately 450 to 100 ...

Elsevier2024

Dataset for "Complexity of crack front geometry enhances toughness of brittle solids"

John Martin Kolinski, Chenzhuo Li, Xinyue Wei

This data package supports the publication 'Complexity of crack front geometry enhances toughness of brittle solids' by Xinyue Wei, Chenzhuo Li, Cían McCarthy, and John M. Kolinski Nature physics (2024) - https://doi.org/10.1038/s41567-024-02435-x DOI: 1 ...

Zenodo2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Modeling friction and wear using an adaptive discrete-continuum coupling

Manon Eugénie Voisin--Leprince

When two objects slide against each other, wear and friction occur at their interface. The accumulation of wear forms what is commonly referred to as a ``third-body''. Understanding third-body evolution has significant applications in industry, where contr ...

EPFL2024

Pyroresistive response of percolating conductive polymer composites

Claudio Grimaldi

The pyroresistive response of conductive polymer composites (CPCs) has attracted much interest because of its potential applications in many electronic devices requiring a significant responsiveness to changes in external physical parameters such as temper ...

Amer Physical Soc2024

Strain Gradients and Magnetoresistance in Microstructured 3D Topological Semi-metals

Jonas De Jesus Diaz Gomez

Three-dimensional topological semimetals have emerged as strong candidates to probe new fundamental physical phenomena that could be exploited to develop next generation electronics. However, many aspects of their electronic properties remain unclear. Thi ...

EPFL2023

Deformation response of highly stretchable and ductile graphene kirigami under uniaxial and biaxial tension

Ye Wei, Yao Chen, Tong Guo

Kirigami, the ancient technique of paper cutting, has been successfully applied to enhance the stretchability and ductility of nanoscale graphene. However, existing experimentally realized graphene kirigami (GK) are created by introducing parallel cuts, ex ...

Amer Physical Soc2023

Energy dissipation in fiber-polymer composites adhesive joints under cyclic loading

Ghazaleh Eslami

Sustainable development has emerged as a paramount consideration in various fields of industry, including construction, to preserve the environment and its finite resources. Lightweight structures, such as fiber-polymer composite structures, address both s ...

EPFL2023

Atomic-scale Characterization of Strain and Gate effects on Two-dimensional Materials by Scanning Tunneling Microscopy

Jz -Yuan Juo

Strain is an inevitable phenomenon in two-dimensional (2D) material, regardless of whether the film is suspended or supported. Moreover, strain is known to alter the physical and chemical properties, such as the band gap, charge carrier effective masses, d ...

EPFL2023

On the slip burst amplitude cutoff in dislocation-rich microcrystals

Andreas Mortensen, Luciano Borasi

The plastic deformation of small-scale face-centered cubic metals exhibits intermittent slip burst events that appear on stress-strain curves as sudden strain jumps and/or load drops. These events are generally attributed to the avalanche-like cooperative ...

Pergamon-Elsevier Science Ltd2023

Experimental investigation of rotational behavior of pseudo-ductile adhesive angle joints exhibiting variable strain rate

Thomas Keller, Abdolvahid Movahedirad, Ghazaleh Eslami

Pseudo-ductile behavior in composite structural frames can be achieved by enabling their beam-column joints to exhibit nonlinear structural response due to progressive damage, by using pseudo-ductile adhesives. This study investigates the static behavior o ...

2023

Bounding the localized to ductile transition in porous rocks: implications for geo-reservoirs

Marie Estelle Solange Violay, Gabriel Gérard Dominique Meyer

Porous rocks have long been the focus of intense research driven by their importance in our society as host to our most essential resources (oil, gas, water, geothermal energy, etc), yet their rheology remains poorly understood. With increasing depth, poro ...

2023

A reduced-order, rotation-based model for thin hard-magnetic plates

Pedro Miguel Nunes Pereira de Almeida Reis, Dong Yan, Bastien Freddy Gustave Aymon

We develop a reduced-order model for thin plates made of hard magnetorheological elastomers (hard-MREs), which are composed of hard-magnetic particles embedded in a polymeric matrix. First, we propose a new magnetic potential, as an alternative to an exist ...

PERGAMON-ELSEVIER SCIENCE LTD2023

Room-temperature strength of the interfacial bond between silica inclusions and iron

Andreas Mortensen, Alejandra Inés Slagter, David Hernandez Escobar, Sergio Perosanz Amarillo

The strength of the interface between iron (Fe) and individual spherical silica (SiO2) inclusions of 5 +/- 1 mu m diameter is measured by means of in-situ micro-cantilever bending tests conducted under displacement control within a scanning electron micros ...

Pergamon-Elsevier Science Ltd2023

Lattice Green's function method for Atomistic/Continuum coupling

Ankit Gupta

Metal plasticity is an inherently multiscale phenomenon due to the complex long-range field of atomistic dislocations that are the primary mechanism for plastic deformation in metals. Atomistic/Continuum (A/C) coupling methods are computationally efficient ...

EPFL2023

Laser powder bed fusion of Fe-based shape memory alloys for novel structural metamaterials and "smart" structures

Irene Ferretto

Laser powder bed fusion (LPBF) is a powder-based additive manufacturing (AM) technique, which shows great potential in the production of complex-shaped parts with unprecedented design freedom. In addition, it allows for an active manipulation of the micros ...

EPFL2023

Simple shear extrusion versus equal channel angular pressing: A comparative study on the microstructure and mechanical properties of an Mg alloy

Cyril Cayron, Roland Logé, Aryan Rezaei Rad

Two severe plastic deformation (SPD) techniques of simple shear extrusion (SSE) and equal channel angular pressing (ECAP) were employed to process an extruded Mg -6Gd -3Y -1.5Ag (wt%) alloy at 553 K for 1, 2, 4 and 6 passes. The microstructural evolutions ...

KEAI PUBLISHING LTD2023

Nanoindentation of embedded particles

Andreas Mortensen, Alejandra Inés Slagter, Joris Pierre Everaerts

We address the effect of elastic inhomogeneity on elastic modulus and hardness determinations made by depth-sensing indentations performed on individual particles embedded within a matrix of different elastic modulus. Finite element simulations and nanoind ...

SPRINGER HEIDELBERG2023