Publications associées à Development of Novel Standardized Structural Timber Elements Using Wood-Wood Connections

FLO:RE – A new floor system made of reused reinforced concrete and steel elements

Maléna Bastien Masse, Numa Joy Bertola, Célia Marine Küpfer, Corentin Jean Dominique Fivet

Carefully extracting reinforced concrete (RC) elements from soon-to-be demolished structures and reusing them as load-bearing components is an emerging circular low-carbon alternative to building new structures. As floor construction typically accounts for ...

IABSE2024

Teaching Not To

Charlotte Malterre-Barthes

Two design studios were successively taught in two schools of architecture: one at the Harvard Graduate School of Design (GSD) and the other at the Swiss Federal Institute of Technology in Lausanne (EPFL) in Lausanne, Switzerland, based on "A Global Morato ...

Taylor & Francis Inc2024

Instabilities in Elastic and Magneto-Elastic Beams and Shells: from Shell Buckling to the Design of a Programmable Braille Reader

Arefeh Abbasi

In this thesis, we conduct a comprehensive investigation into structural instabilities of both elastic and magneto-elastic beams and shells, resulting in a creative proposal to design a programmable braille reader. Methodologically, we combine numerical si ...

EPFL2024

Experimental Investigation on Size-Effect of Rubble Stone Masonry Walls Under In-Plane Horizontal Loading: Overview and Preliminary Results

Katrin Beyer, Savvas Saloustros

Rubble stone masonry is a common construction typology of historical city centres and vernacular architecture. While past earthquakes have shown that it is one of the most vulnerable masonry construction typologies, there are few experimental campaigns giv ...

2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

A global framework for data-informed bridge examination

Eugen Brühwiler, Philippe Schiltz, Numa Joy Bertola

Examining the performance of an existing bridge requires information on several aspects, such as design choices, material properties, and ongoing degradation processes. It often happens that some critical information is not available. The traditional appro ...

2024

A Softening Constitutive Law and Gradient-Inelastic Fiber-Based Element for 3-Dimensional Frame Simulations Under Seismic Excitations

Diego Isidoro Heredia Rosa

Steel frame structures are essential components of modern infrastructure. Understanding their behavior under seismic loading is critical for ensuring public safety and minimizing damage that occurs during earthquakes. To accurately predict the response of ...

EPFL2024

Embodied Carbon Premium for Cantilevers

David Michael Volpe Ruggiero, Paola Costanza Miglietta

This study addresses the critical need for sustainable architectural designs within the context of climate change and the significant role the built environment plays in greenhouse gas emissions. The focus of this paper is on understanding the influence of ...

2024

Reuse of cut concrete slabs in new buildings for circular ultra-low-carbon floor designs

Numa Joy Bertola, Célia Marine Küpfer, Corentin Jean Dominique Fivet

The study explores an original idea that responds to the urgent need to reduce the detrimental environmental impacts of load-bearing floor construction in new buildings by reusing saw-cut reinforced concrete (RC) pieces salvaged from soon-to-be demolished ...

2024

An explorative method to support design decisions based on carbon constraints and daylight sufficiency needs

Nazanin Rezaei Oghazi

The global construction industry contributes to 37% of carbon emissions associated to both building operations and construction. To help achieve the net-zero targets set by 2050, it is mandated to achieve a 50% reduction in carbon emissions by 2030. As we ...

EPFL2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Structure and dynamics of liquid water from ab initio simulations: adding Minnesota density functionals to Jacob's ladder

Ursula Röthlisberger, Justin Villard, Martin Peter Bircher

The accurate representation of the structural and dynamical properties of water is essential for simulating the unique behavior of this ubiquitous solvent. Here we assess the current status of describing liquid water using ab initio molecular dynamics, wit ...

Royal Soc Chemistry2024

Influence of fiber orientation on the tensile behavior of UHPFRC and reinforced UHPFRC under static and fatigue loadings

Jian Zhan

Ultra-high performance fiber reinforced cementitious composite (UHPFRC) is a modern class of cementitious building materials. Because of its superior mechanical properties and durability, it is increasingly used globally to rehabilitate, strengthen and mod ...

EPFL2024

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Marko Pejatovic

Codes of practice can be overly conservative, particularly for the shear resistance of reinforced concrete beams with shear reinforcement when large loads act close to supports. This thesis addresses the topic by proposing a refined design approach based o ...

EPFL2024

Methods to assess the carbon footprint of structures involving UHPFRC elements

Eugen Brühwiler, Numa Joy Bertola, Antonina Hochuli

The development of Ultra-High Performance Fibre-Reinforced Cementitious Composite (UHPFRC) has enabled the design of lightweight constructions. Although the greenhouse gas emissions of UHPFRC per volume are higher than that of conventional concr ...

Kassel University Press2024

Numerical Modeling of FRP-Strengthened Masonry Structures Using Equivalent Frame Models

Katrin Beyer, Francesco Vanin, Ivana Bozulic

The present study focuses on enhancing the seismic resistance of existing masonry structures. To that aim, the use of fiber-reinforced polymer (FRP) strengthening serves to improve structural behaviour by attaching FRP strips to the masonry walls. Despite ...

Springer2024

The Current State of the OBI DICT Project: A Bilingual e-Dictionary of Oracle-Bone Inscriptions with AI Image Recognition

This article reports on the current state of the OBI DICT project, a bilingual e-dictionary of oracle-bone inscriptions (OBI), incorporating artificial intelligence (AI) image recognition technology. It first provides a brief overview of the development of ...

Buro Van Die Wat2024

Course Design - A Visual and Modular Approach

Marc Laperrouza

This book has been designed for instructors in higher education or adult training who wish to develop a new course or revise an existing one. It adopts a practical, visual, and modular approach based on the principle of constructive alignment. At its heart ...

EPFL Press2024

Models implemented in the methodological approach to design the initial STEP first wall contour

Kevin Henricus Annemarie Verhaegh, Dario Vaccaro, Filippo Bagnato, Davide Galassi

The official Spherical Tokamak for Energy Production mission aims to demonstrate the ability to generate net electricity from fusion with the STEP Prototype Power plant. One of the key technological and engineering challenges in fusion power plants is mana ...

Elsevier Science Sa2024