Publications associées à Development of the Mechanical Properties of an Ultra-High Performance Fiber Reinforced Concrete (UHPFRC)

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Reusability assessment of reinforced concrete components prior to deconstruction from obsolete buildings

Maléna Bastien Masse, Julie Rachel Devènes, Corentin Jean Dominique Fivet

A large part of building demolitions is motivated by purely socio-economic reasons. Hence, about-to-be-demolished structures, commonly made of reinforced concrete, very often present no or little degradation. When adaptive reuse of the entire building is n ...

2024

Additively manufactured steel reinforcement for small scale reinforced concrete modeling: Tensile and bond behavior

Christian Leinenbach, Rafal Wróbel

Small scale (1:30-1:40) Reinforced Concrete is useful for centrifuge testing. However, manufacturing the reinforcing cages by hand at this scale is practically difficult. This paper suggests that small scale reinforcement can be manufactured using a metal ...

Elsevier Sci Ltd2024

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Marko Pejatovic

Codes of practice can be overly conservative, particularly for the shear resistance of reinforced concrete beams with shear reinforcement when large loads act close to supports. This thesis addresses the topic by proposing a refined design approach based o ...

EPFL2024

Experimental investigation of dowel action in reinforcing bars using refined measurements

Aurelio Muttoni, Marko Pejatovic

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

Ernst & Sohn2024

Decarbonization potential of steel fibre-reinforced limestone calcined clay cement concrete one-way slabs

Hisham Tarek Mohamed Hafez

This study deals with a comparison of the environmental performance of one-way slabs utilizing steel fibrereinforced limestone calcined clay cement (LC3) concrete with the control case of Ordinary Portland cement concrete. The experimental program constitu ...

Elsevier Sci Ltd2024

Influence of fiber orientation on the tensile behavior of UHPFRC and reinforced UHPFRC under static and fatigue loadings

Jian Zhan

Ultra-high performance fiber reinforced cementitious composite (UHPFRC) is a modern class of cementitious building materials. Because of its superior mechanical properties and durability, it is increasingly used globally to rehabilitate, strengthen and mod ...

EPFL2024

Contributions to rebar-to-concrete interaction and its structural implications for design and monitoring applications

Enrique Corres Sojo

Bond between reinforcing bars and concrete has been the focus of extensive research over the last century. This is well-justified as the functioning of reinforced concrete intimately depends on the interaction between rebar and concrete, as for example cra ...

EPFL2024

Water weakening and the compressive brittle strength of carbonates: Influence of fracture toughness and static friction

Marie Estelle Solange Violay, Barnaby Padraig Fryer, Corentin Jean-Marie Rémi Noël

Water is ubiquitous within the pore space of rocks and has been shown to affect their physical and mechanical behaviour. Indeed, water can act on the rock strength via mechanical (i.e., reducing the effective stresses) or chemical effects (e.g., mineral di ...

2024

Estimation of the bar stress based on crack width measurements in reinforced concrete structures

Aurelio Muttoni, Enrique Corres Sojo

Estimating the stress of reinforcing bars and its variations in service conditions can be useful to determine the reserve capacity of structures or to assess the risk of fatigue in the reinforcement. This paper investigates the use crack width measurements ...

Ernst & Sohn2024

Exploring the potential of the critical shear crack theory for reinforced and post-tensioned glass beams: Initial analysis and experiments

Alain Nussbaumer, Pieter Christian Louter, Jagoda Cupac

In the evolution of structural glass beam elements, the requirements for post-fracture load bearing capacity and safe failure behaviour have led to the development of reinforced and post-tensioned beams. Maximum bending capacity in the post-fracture state ...

2023

A Discussion on the Reliability of prEN1992-1-1:2021 Shear Strength Provisions for Fibre Reinforced Concrete Members Without Shear Reinforcement

Miguel Fernández Ruiz

The Eurocode 2 for the design of concrete structures (EN1992-1-1:2004) is undergoing a revision that will lead to the publication of the second generation of this code to be used across all CEN member countries. Therefore, the impact of the code will reach ...

SPRINGER INTERNATIONAL PUBLISHING AG2023

Reinforcement bond performance in 3D concrete printing: Explainable ensemble learning augmented by deep generative adversarial networks

Xianlin Wang

Integrating various reinforcements into 3D concrete printing (3DCP) is an efficient method to satisfy critical requirements for structural applications. This paper explores an explainable ensemble machine learning (EML) method to predict the bond failure m ...

Elsevier2023

Experimental testing and structural analysis of composite tile – reinforced concrete domes

Savvas Saloustros

Conventional formworks for concrete curved shells either are expensive, complex and wasteful or have formal restrictions. Using tile vaults (also known as timbrel, Guastavino, thin-tile or Catalan vaults) as stay-in-place formwork for concrete shells could ...

2023

Environmental and Life-Cycle Cost Evaluation of a Composite Timber-UHPFRC Bridge

Eugen Brühwiler, Numa Joy Bertola

Ultra-High-Performance Fibre Reinforced Cementitious Composite (UHPFRC) has recently been used to design lightweight structures and strengthen existing ones, with more than 300 applications in Switzerland. Several composite timber-UHPFRC bridges have been ...

2023

Low-tech methods for the reuse of reinforced concrete structural elements

Maléna Bastien Masse, Julie Rachel Devènes, Corentin Jean Dominique Fivet, Nicole Widmer

Most of existing buildings are made of concrete, new buildings are being built with it and others are demolished when still in good structural condition. This drives increased demands for raw materials, greenhouse gas emissions, and an accumulation of demo ...

2023

Does carbon footprint reduction impair mechanical properties and service life of concrete?

Karen Scrivener, Diana Londoño Zuluaga

The aim of this study is to evaluate how much the changes in the concrete mix design, which enable carbon footprint reduction, are impacting mechanical properties and predicted service life of concrete structure. The starting point of this study was concre ...

SPRINGER2023

Automatic and high-precision acoustic emission-based structural health monitoring of concrete structures

Brice Tanguy Alphonse Lecampion, Seyyedmaalek Momeni

Acoustic emission (AE) monitoring is a useful technique to monitor the health of a structure continuously, helping to prevent potential failure. AE are elastic waves produced and emitted during fracture processes inside a material and are recorded by senso ...

DESTech publications inc.2023

Multi-scale characterization and modeling of notched strength and translaminar fracture in hybrid thin-ply composites based on different carbon fiber grades

Guillaume Clément Broggi

Owing to their high specific stiffness and strength, Carbon Fiber Reinforced Composites (CFRP) are ideal candidates for the development of lightweight high-performance structures. Within this family, thin-ply composites allow for wider design freedom and p ...

EPFL2023