Publications associées à Functional composites with damage control and repair

Self-catalysed frontal polymerisation enables fast and low-energy processing of fibre reinforced polymer composites

Véronique Michaud, Baris Çaglar, Jacobus Gerardus Rudolph Staal

Frontal polymerisation has the potential to bring unprecedented reductions in energy demand and process time to produce fibre reinforced polymer composites. Production of epoxy-based fibre reinforced polymer parts with high fibre volume content, commonly e ...

2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Two-dimensional quasi-static delamination in composite laminates under Mode-I and Mode-II conditions

Congzhe Wang

Fiber-polymer composites consist of a polymer matrix and reinforcing fibers made of various materials. These composites exhibit exceptional properties, such as a high strength-to-weight ratio and excellent corrosion resistance, which has led to their incre ...

EPFL2024

Additive Manufacturing of Bioinspired Mineral-Based Composites

Ran Zhao

Biominerals are used by natural organisms for example as structural supports and optical sensors. They are produced from a limited number of elements and under ambient conditions. Nevertheless, they often possess excellent mechanical properties and sometim ...

EPFL2024

Enabling simultaneous reprocessability and fire protection via incorporation of phosphine oxide monomer in epoxy vitrimer

Véronique Michaud, Valentin Rougier

The conception of epoxy thermosets with both reprocessability and flame retardancy delineates a new horizon in polymer science, offering a material solution that is not only superior in fire safety but is also environment friendly. Herein, a flame-retardan ...

Journal Mater Sci Technol2024

On the influence of flow-front orientation on stringer stiffened composite panels in water impacts

Véronique Michaud

Water impacts form the critical load case for high-performance carbon fibre reinforced polymer (CFRP) racing craft. Such events produce a peaked, non-uniform pressure distribution that travels along a hull panel as it is immersed. Current design standards ...

2024

Biobased Composites from Eugenol- and Coumarin-Derived Methacrylic Latex and Hemp Nanocellulose: Cross-Linking via [2+2] Photocycloaddition and Barrier Properties

Yves Leterrier, Sara Dalle Vacche

A novel-biobased latex was synthesized by redox-initiated emulsion copolymerization of ethoxy dihydroeugenyl methacrylate with 5 wt % of a photosensitive methacrylate containing a coumarin group. A stable copolymer latex having 16 wt % solids content and a ...

Amer Chemical Soc2024

Process-Induced Structures of Injection-Molded High-Density Polyethylene-Combining X-ray Scattering and Finite Element Modeling

Marianne Liebi, Manuel Guizar Sicairos

The success of plastics heavily relies on fast melt processing methods used for large-scale industrial manufacturing, including injection molding. The hierarchical structure of the solid polymer depends on material selection combined with processing condit ...

Amer Chemical Soc2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Numerical investigation of two-dimensional Mode-II delamination in composite laminates

Thomas Keller, Anastasios Vassilopoulos, Congzhe Wang

Existing standards for delamination tests on composite materials typically employ one-dimensional (1D) beam specimens. However, such specimens may not represent real delamination scenarios in composite structures, where cracks tend to propagate in two dime ...

Elsevier Sci Ltd2024

Highly anisotropic carbon fiber electrodes for DEAs and their dynamic non-monotonic conductive properties

Yves Perriard, Stefania Maria Aliki Konstantinidi, Markus Koenigsdorff

A common method for creating compliant electrodes for dielectric elastomer actuators (DEAs) and soft sensors is to incorporate electrically conductive carbon particles into a polymer matrix. However, using unidirectional aligned carbon fibers instead not o ...

Society of Photo-Optical Instrumentation Engineers (SPIE)2024

Incorporation of Lignin in Bio-Based Resins for Potential Application in Fiber-Polymer Composites

Mário Alexandre De Jesus Garrido, Mateus De Assunção Hofmann

Bio-based resins, obtained from renewable raw materials, are a more sustainable alternative to oil-based resins for fiber-reinforced polymer (FRP) composites. The incorporation of lignin in those resins has the potential to enhance their performance. This ...

MDPI2023

Strategies for energy-efficient frontal polymerisation processing and microstructural evaluation of fibre reinforced composites

Jacobus Gerardus Rudolph Staal

Liquid composite moulding methods are widely applied for manufacturing of fibre reinforced polymer (FRP) composites and consist of two main stages: impregnation of fibrous reinforcements by a liquid monomer resin and curing of this resin. This thesis work ...

EPFL2023

Recyclable flame retardant phosphonated epoxy based thermosets enabled via a reactive approach

Véronique Michaud, Valentin Rougier

The development of reusable fire-safe polymers with a prolonged lifetime heralds the switch for a transition towards circular economy. In this framework, we report a novel phosphonated thermoset which is composed of networked phosphonate esters containing ...

ELSEVIER SCIENCE SA2023

Supramolecular Modifications of Semicrystalline Polymers

Michael Alan Giffin

Supramolecular interactions play an important role in defining the structure and the resulting mechanical properties of materials. For instance, interchain hydrogen-bonding in PAs gives them superior strength and stiffness in engineering materials, while t ...

EPFL2023

Multi-scale characterization and modeling of notched strength and translaminar fracture in hybrid thin-ply composites based on different carbon fiber grades

Guillaume Clément Broggi

Owing to their high specific stiffness and strength, Carbon Fiber Reinforced Composites (CFRP) are ideal candidates for the development of lightweight high-performance structures. Within this family, thin-ply composites allow for wider design freedom and p ...

EPFL2023

CRACK SHIELDING MECHANISMS OF INTERLAYERED EPOXY MATERIALS UNDER QUASI-STATIC AND FATIGUE LOADING

Anastasios Vassilopoulos, Dharun Vadugappatty Srinivasan

This research explores the capability of PEI and PVDF thermoplastic interlayers to arrest cracks in epoxy materials modified with short-glass fibers and core-shell rubber particles. It also investigates the effect of interlayer position, the number of inte ...

Queen's University Belfast2023

Energy dissipation in fiber-polymer composites adhesive joints under cyclic loading

Ghazaleh Eslami

Sustainable development has emerged as a paramount consideration in various fields of industry, including construction, to preserve the environment and its finite resources. Lightweight structures, such as fiber-polymer composite structures, address both s ...

EPFL2023

Visualization and modelling of dynamic flow in fibrous preforms for liquid composite molding

Helena Luisa Teixido Pedarros

Nowadays, Liquid Composite Molding techniques are often used to manufacture high quality fiber reinforced composite parts at a relatively low cost. These involve an infiltration process, in which a liquid resin is forced to ingress into a dry fibrous porou ...

EPFL2023