Publications associées à Low-Stress Hyperbranched Polymer/Silica Nanostructures Produced by UV Curing, Sol/Gel Processing and Nanoimprint Lithography

Two-dimensional quasi-static delamination in composite laminates under Mode-I and Mode-II conditions

Fiber-polymer composites consist of a polymer matrix and reinforcing fibers made of various materials. These composites exhibit exceptional properties, such as a high strength-to-weight ratio and excellent corrosion resistance, which has led to their incre ...

EPFL2024

Tailor-made Piezoelectric Elastomer Materials

Francis Owusu

Recent advancements in miniature devices with higher computational capabilities and ultralow power consumption have accelerated the development of wearable sensors, actuators, and energy harvesters everywhere. The ultimate aim of such a technological revol ...

EPFL2023

Controlling the Microstructure and Composition of 3D Printed Soft Load-Bearing Hydrogels

Matteo Hirsch

Hydrogels are among the first materials expressly designed for their use in biomedicine. However, state-of-the-art applications of hydrogels are severely limited because they are typically either too soft or too brittle such that they cannot bear significa ...

EPFL2023

Fractal Analysis of Four Xerogels Based on TEGylated Phenothiazine and Chitosan

Maria-Alexandra Paun

The present article describes novel massive materials (in the solid phase) based on TEGylated phenothiazine and chitosan that possess great capability to recover mercury ions from constituent aqueous solutions. These were produced by chitosan hydrogelation ...

MDPI2023

Process development of pre-impregnated hybrid thin-ply composites

Alexios Argyropoulos

Thin-ply composites, obtained with recently developed fiber spreading techniques, rapidly gained industrial interest because they offer a large composite design freedom, and lead to a composite tensile strength that is close to that of the individual fiber ...

EPFL2023

Semiconductor-based device architectures in multimaterial fibers

William Nicolas Duncan Esposito

Semiconductor materials have given rise to today's digital technology and consumer electronics. Widespread adoption is closely linked to the ability to process and integrate them in devices at scale. Where flexibility and large surfaces are required, such ...

EPFL2023

Incorporation of Lignin in Bio-Based Resins for Potential Application in Fiber-Polymer Composites

Mário Alexandre De Jesus Garrido, Mateus De Assunção Hofmann

Bio-based resins, obtained from renewable raw materials, are a more sustainable alternative to oil-based resins for fiber-reinforced polymer (FRP) composites. The incorporation of lignin in those resins has the potential to enhance their performance. This ...

MDPI2023

Optical manipulation of plasmonic nanoparticles: Applications in surface chemistry and nano-optics

Jeonghyeon Kim

Optical tweezers are devices that can manipulate nano- and microparticles using a laser. The principle of optical tweezers is to apply a force to an object using the momentum of light. This force is very small, but it is sufficient to move things in the mi ...

EPFL2023

Capillary Effects in Fiber Reinforced Polymer Composite Processing: A Review

Véronique Michaud, Baris Çaglar, Jacobus Gerardus Rudolph Staal, Helena Luisa Teixido Pedarros

Capillarity plays a crucial role in many natural and engineered systems, ranging from nutrient delivery in plants to functional textiles for wear comfort or thermal heat pipes for heat dissipation. Unlike nano- or microfluidic systems with well-defined por ...

FRONTIERS MEDIA SA2022

Multiscale microshaping of functionally graded polymer-derived SiCN ceramics

Lorenz Hagelüken

Polymer-derived ceramics (PDCs) exhibit excellent properties and are compatible with many shaping techniques due to the liquid character of the preceramic polymers (PCPs). Furthermore, their properties are adjustable by modifying the precursor composition ...

EPFL2022

Role of Stress History on the Swelling-Shrinkage Behavior of Compacted Scaly Clay

Alessio Ferrari

Compacted scaly clays are complex geomaterials widely used for the realization of dam cores and waste dump liners. This research aims to investigate the swelling/shrinkage behavior of these geomaterials subjected in an oedometric cell to complex hydromecha ...

ASCE-AMER SOC CIVIL ENGINEERS2022

Dielectric properties of 3-3 flexible composites by infiltration of elastomers into porous ceramic structures using cellulose scaffold

Frank Nüesch, Thomas Geiger

Elastomer composites are prepared by infiltrating polydimethylsiloxane (PDMS) into a porous ceramic structure of nanoparticles. This method differs from the conventional approach, where particles are dispersed into the polymer matrix, since here, the polym ...

PERGAMON-ELSEVIER SCIENCE LTD2022

Drops: Controlled crystallization of organic crystals and their use as matrix materials for encapsulation of volatiles

Aysu Ceren Okur

Encapsulation techniques open up new possibilities to control the kinetics and location of the release of active ingredients. Despite the progresses achieved to obtain a better control over the dimensions and composition of the capsules, the encapsulation ...

EPFL2022

Controlling motion at the nanoscale with light

Mintae Chung

Optical manipulation at the micro- nano-scale is a fascinating topic due to its inherent non-invasive properties and multifaceted applications in various fields such as biology, sensing, micro-fluidics, and micro- nano-robotics. This thesis involves intens ...

EPFL2022

Light-induced assembly and disassembly of polymers with PdnL2n-type network junctions

Kay Severin, Cristian Pezzato, Cesare Berton, Rujin Li

Polymers containing PdnL2n complexes as network junctions were obtained by reaction of poly(ethylene glycol)-linked N-donor ligands with Pd2+. The addition of a metastable state photoacid renders the networks light sensitive, and gel–sol transitions can be ...

2021

Femtosecond laser-based optomechanical processes for permanent and high-precision fine alignment of optical systems

Saood Ibni Nazir

Miniaturization has been at the forefront of scientific research in the past decade covering diverse areas such as electronics, mechanics, and optics. While 'small is beautiful' may be a vast generalization, the true benefits of miniaturization are especia ...

EPFL2021

Surface energy contributions to the work of infiltration in metal matrix composite processing

Andreas Mortensen, Gionata Schneider

The work needed to mechanically drive molten metal into a porous solid preform when producing a composite material by infiltration can significantly exceed the energy change required for thermodynamically reversible infiltration. We measure, by quantitativ ...

2021

Nanopillars Enabling III-V Integration on Si (100) and (111)

Lucas Güniat

The majority of current semiconductor technologies are built on Si (100), such as the CMOS technology, or conventional solar cell devices. III-V semiconductors offer great perspectives given their high carrier mobility and direct band gap. However their in ...

EPFL2021

Study and characterization of silicon metal alloys systems for the reactive infiltration process of ceramic matrix composites

Manoj Kondibhau Naikade

Silicon infiltrated silicon carbide (SiSiC) is one of the most promising and economical non-oxide ceramic matrix composites for high-temperature structural applications. In recent years infiltration by Si-alloys instead of pure Si has become popular to avo ...

EPFL2021

Design and Development of Injectable, Tough and Intrinsically-Adhesive Hydrogels for Biomedical Applications

Peyman Karami

Despite the development of hydrogels with a wide range of mechanical properties, insufficient adhesion between these materials and biological surfaces limits their use in the biomedical applications. Most recent advancements in highly adhesive hydrogel sys ...

EPFL2021