Publication

Effects of residual stresses on the tensile fatigue behavior of concrete

Publications associées (29)

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Influence of fiber orientation on the tensile behavior of UHPFRC and reinforced UHPFRC under static and fatigue loadings

Jian Zhan

Ultra-high performance fiber reinforced cementitious composite (UHPFRC) is a modern class of cementitious building materials. Because of its superior mechanical properties and durability, it is increasingly used globally to rehabilitate, strengthen and mod ...

EPFL2024

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Xhemsi Malja

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Strain engineering and strain measurement by spring tethers on suspended epitaxial GaN-on-Si photonic crystal devices

Romuald Houdré, Jun Wang

Suspended epitaxial gallium nitride (GaN) on silicon (Si) photonic crystal devices suffer from large residual tensile strain, especially for long waveguides, because fine structures tend to crack due to large stress. By introducing spring-like tethers, des ...

Iop Publishing Ltd2024

Water weakening and the compressive brittle strength of carbonates: Influence of fracture toughness and static friction

Marie Estelle Solange Violay, Barnaby Padraig Fryer, Corentin Jean-Marie Rémi Noël

Water is ubiquitous within the pore space of rocks and has been shown to affect their physical and mechanical behaviour. Indeed, water can act on the rock strength via mechanical (i.e., reducing the effective stresses) or chemical effects (e.g., mineral di ...

2024

Proposed residual stress model for hot‐rolled wide flange steel cross sections

Albano António De Abreu E Presa De Castro E Sousa, Dimitrios Lignos, Andronikos Skiadopoulos

Residual stresses in hot-rolled wide flange steel cross sections may lead to premature yielding, accelerated corrosion and brittle fracture of steel members. The above phenomena lead to a loss of a steel member's stiffness and resistance under mechanical l ...

Ernst & Sohn2023

Geometric tolerances of welded connections with inelastic panel zones

Dimitrios Lignos, Andronikos Skiadopoulos, Ce Wen

Prequalified beam-to-column connections in steel moment resisting frames usually concentrate inelastic deformations in the steel beam ends. As such, nonlinear geo-metric instabilities (i.e., local buckling) may occur in these regions at modest lateral drif ...

Ernst & Sohn2023

Nanomechanical Modeling of the Bending Response of Silicon Nanowires

Yusuf Leblebici, Zuhal Tasdemir, Mustafa Yilmaz, Mohammad Nasr Esfahani

Understanding the mechanical behavior of silicon nanowiresis essentialfor the implementation of advanced nanoscale devices. Although bendingtests are predominantly used for this purpose, their findings shouldbe properly interpreted through modeling. Variou ...

AMER CHEMICAL SOC2023

Experiments and proposed model for residual stresses in hot-rolled wide flange shapes

Albano António De Abreu E Presa De Castro E Sousa, Dimitrios Lignos, Andronikos Skiadopoulos

This paper proposes a new residual stress model for hot-rolled wide flange steel cross sections. For this purpose, a dataset of 85 residual stress measurements is first assembled. The dataset is comprised of prior measurements available in the literature t ...

2023

Room-temperature strength of the interfacial bond between silica inclusions and iron

Andreas Mortensen, Alejandra Inés Slagter, David Hernandez Escobar, Sergio Perosanz Amarillo

The strength of the interface between iron (Fe) and individual spherical silica (SiO2) inclusions of 5 +/- 1 mu m diameter is measured by means of in-situ micro-cantilever bending tests conducted under displacement control within a scanning electron micros ...

Pergamon-Elsevier Science Ltd2023

Database of Residual Stress Measurements on Hot-rolled Wide Flange Steel Cross Sections

Albano António De Abreu E Presa De Castro E Sousa, Dimitrios Lignos, Andronikos Skiadopoulos

Data_info.csv: Database of 'Residual Stress Measurements on Hot-rolled Wide Flange Steel Cross Sections' including cross-sectional and material characteristics as well as information relevant to ploting the residual stress distributions. Distributions.zip: ...

Zenodo2023

Deformation response of highly stretchable and ductile graphene kirigami under uniaxial and biaxial tension

Ye Wei, Yao Chen, Tong Guo

Kirigami, the ancient technique of paper cutting, has been successfully applied to enhance the stretchability and ductility of nanoscale graphene. However, existing experimentally realized graphene kirigami (GK) are created by introducing parallel cuts, ex ...

Amer Physical Soc2023

Microscopic Digital Image Correlation Analysis of Strain Distributions in Stainless Steel 316L Induced by Multiaxial Cyclic Loading

Elif Cansu Kursun

Fatigue damage in materials results in localized strain at the microstructural level. In many engineering components of the cooling circuits of nuclear power plants, where austenitic steels are used, the material experiences multiaxial cyclic loading, eith ...

EPFL2023

Experimental Evaluation and Modeling of Residual Stress Distributions for Hot-Rolled Wide Flange Steel Members

Albano António De Abreu E Presa De Castro E Sousa, Dimitrios Lignos, Andronikos Skiadopoulos

Local and member instability modes in structural steel members are influenced by initial geometric imperfections and residual stresses among other parameters. The robustness of stability-related design provisions and finite element modeling procedures of s ...

2023

Multi-scale characterization and modeling of notched strength and translaminar fracture in hybrid thin-ply composites based on different carbon fiber grades

Guillaume Clément Broggi

Owing to their high specific stiffness and strength, Carbon Fiber Reinforced Composites (CFRP) are ideal candidates for the development of lightweight high-performance structures. Within this family, thin-ply composites allow for wider design freedom and p ...

EPFL2023

On the slip burst amplitude cutoff in dislocation-rich microcrystals

Andreas Mortensen, Luciano Borasi

The plastic deformation of small-scale face-centered cubic metals exhibits intermittent slip burst events that appear on stress-strain curves as sudden strain jumps and/or load drops. These events are generally attributed to the avalanche-like cooperative ...

Pergamon-Elsevier Science Ltd2023

Energy dissipation in fiber-polymer composites adhesive joints under cyclic loading

Ghazaleh Eslami

Sustainable development has emerged as a paramount consideration in various fields of industry, including construction, to preserve the environment and its finite resources. Lightweight structures, such as fiber-polymer composite structures, address both s ...

EPFL2023

Strengthening mechanisms in dilute and random solid solution high-entropy BCC alloys

Alireza Ghafarollahi

Tuning the mechanical properties of metals, including strength, through adjusting the type and/or concentration of added solute elements, has been recognized as an effective way to design and produce materials with desired or optimized mechanical propertie ...

EPFL2022

Experimental investigation of dowel action using advanced measurement techniques

Aurelio Muttoni, Marko Pejatovic

Existing shear-cracked structures need to be reliably verified in order to avoid redundant interventions. Code provisions often raise shear safety and/or fatigue life concerns of the reinforcement subjected to stress concentrations due to cyclic dowel acti ...

2022

FEM of stress partition during compression of WC-10 wt.% Co with realistic 3D morphology

Daniele Mari, Lucas Eric Jacques Degeneve

A Finite Element Model is developed to represent the mechanical behavior of WC-10 wt.% Co in compression tests. In this research, realistic three-dimensional model is obtained by slicing a sample by Focused Ion Beam and reconstituting it, resulting in two ...

ELSEVIER SCI LTD2022