Publication

Effect of fiber architecture on tension-tension fatigue behavior of bolted basalt composite joints

Publications associées (28)

Tension-tension fatigue behavior of basalt composite hybrid joints

The tension–tension fatigue behavior of pseudo-ductile hybrid bonded-bolted double lap basalt composite joints, composed of pseudo-ductile adhesives and adherends with multi-directional fiber architecture, was experimentally investigated. The fatigue damag ...

2024

Strain-based analysis on the influence of local undercut geometry on fatigue crack initiation life

Alain Nussbaumer, Heikki Tapani Remes, Abinab Niraula

The local undercut defects at the weld toe provide a potential initiation site for fatigue cracks and significantly impact the structure's fatigue strength. The influence of continuous undercut depth on fatigue performance is widely studied, but the resear ...

2024

A novel fatigue life prediction methodology based on energy dissipation in viscoelastic materials, synergistic effects of stress level, stress ratio, and temperature

Thomas Keller, Abdolvahid Movahedirad, Lulu Liu

This work introduces a new methodology to predict the fatigue life of viscoelastic materials by considering the creep effect on fatigue behavior under the concurrent effects of stress level, stress ratio, and temperature. The model established based on the ...

2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Landolf-Giosef-Anastasios Rhode-Barbarigos, Tara Habibi

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Fatigue behavior and life prediction of wind turbine blade composite materials

Anastasios Vassilopoulos

Fatigue life prediction of wind turbine rotor blades is a very challenging task, as their failure is led by different failure types that act synergistically. Inherent defects like wrinkles, fiber misalignments, and voids that can be introduced during fabri ...

Woodhead Publishing (Elsevier)2023

CRACK SHIELDING MECHANISMS OF INTERLAYERED EPOXY MATERIALS UNDER QUASI-STATIC AND FATIGUE LOADING

Anastasios Vassilopoulos, Dharun Vadugappatty Srinivasan

This research explores the capability of PEI and PVDF thermoplastic interlayers to arrest cracks in epoxy materials modified with short-glass fibers and core-shell rubber particles. It also investigates the effect of interlayer position, the number of inte ...

Queen's University Belfast2023

Reliability analysis and partial safety format calibration considering the characteristics of the resistance of reinforced concrete structures

Qianhui Yu

Every engineering calculation is an approximation of reality, with inevitable uncertainties involved. This fact implies that a reliability verification accounting for the uncertainties is a necessary step in the design and assessment of structures. Nowaday ...

EPFL2023

Multi-scale characterization and modeling of notched strength and translaminar fracture in hybrid thin-ply composites based on different carbon fiber grades

Guillaume Clément Broggi

Owing to their high specific stiffness and strength, Carbon Fiber Reinforced Composites (CFRP) are ideal candidates for the development of lightweight high-performance structures. Within this family, thin-ply composites allow for wider design freedom and p ...

EPFL2023

Considerations on the partial safety factor format for reinforced concrete structures accounting for multiple failure modes

Aurelio Muttoni, Miguel Fernández Ruiz, Qianhui Yu

The increasing usage of nonlinear analyses for the design of reinforced concrete structures and the necessity of codes of practice to provide a consistent safety format for them is one of the challenges that new generations of codes of practice are facing. ...

ELSEVIER SCI LTD2022

Crack propagation in CFRP laminates under mode I monotonic and fatigue loads: A methodological study

John Botsis, Charlie Joseph Simon Blondeau, Georgios Pappas

Delamination in composite materials is often accompanied by fiber bridging that increases resistance to crack growth. Here, delamination of two unidirectional carbon/epoxy systems was studied under monotonic and displacement-controlled fatigue loading. One ...

ELSEVIER SCI LTD2021

Fatigue of reinforced UHPFRC members and monitoring of fatigue action effects on bridges

Bartlomiej Wojciech Sawicki

The objective of this thesis is to develop knowledge and methods to prevent fatigue failure of bridges. The Fatigue Limit State is investigated from both the demand (S) and resistance (R) side. The S-part focuses on reduction of uncertainties through monit ...

EPFL2021

Uncertainties in the Seismic Assessment of Historical Masonry Buildings

Katrin Beyer, Francesco Vanin, Igor Tomic

Seismic assessments of historical masonry buildings are affected by several sources of epistemic uncertainty. These are mainly the material and the modelling parameters and the displacement capacity of the elements. Additional sources of uncertainty lie in ...

2021

Shear Response of Wet Weak Carbonate Rock/Grout Interfaces Under Cyclic Loading

Eleni Stavropoulou

The development and construction of offshore wind farms requires the correct estimation of the friction that can be mobilised at the rock/grout interface. In conventional studies, the shear behaviour of a joint is usually investigated with laboratory tests ...

2021

Fatigue examination of reinforced-concrete bridge slabs using acoustic emission and strain monitoring data

Imane Bayane

The examination of bridges under service loading is key for understanding their condition and thus for their sustainable and efficient use. The need to extend the service duration of existing bridges is increasing, and therefore, efficient tools for examin ...

EPFL2021

Post-tensioning of glass beams: Analytical determination of the allowable pre-load

Alain Nussbaumer, Pieter Christian Louter, Jagoda Cupac

The effectiveness of post-tensioning in enhancing the fracture resistance of glass beams depends on the level of compressive pre-stress introduced at the glass edge surface that will in service be exposed to tensile stresses induced by bending. Maximum pre ...

2021

Casting position effects on bond performance of reinforcement bars

Aurelio Muttoni, Miguel Fernández Ruiz, Francesco Rafael Alberto Moccia

The phenomena associated with the consolidation of fresh concrete (bleeding and plastic settlement) are commonly considered significant for the bond performance of reinforcement. However, rules to take care of such influence for design are not consistent a ...

ERNST & SOHN2021

Onset of sliding across scales: How the contact topography impacts frictional strength

Jean-François Molinari, Fabian Barras, Ramin Aghababaei

When two solids start rubbing together, frictional sliding initiates in the wake of slip fronts propagating along their surfaces in contact. This macroscopic rupture dynamics can be successfully mapped on the elastodynamics of a moving shear crack. However ...

AMER PHYSICAL SOC2021

The influence of the kinematics of rough surface engagement on the transfer of forces in cracked concrete

Miguel Fernández Ruiz

One of the most instrumental aspects governing the response of structural concrete at ultimate limit state refers to the possibility of developing smeared cracking patterns within a member (associated normally to the presence of sufficient reinforcement fo ...

2021

Optimization of multi-directional fiber architecture for resistance and ductility of bolted FRP profile joints

Thomas Keller, Lulu Liu, Xin Wang

In view of the low structural efficiency of bolted joints in pultruded fiber-reinforced polymer (FRP) profiles with mainly unidirectional (UD) fiber architecture, off-axis plies were considered as an effective way to improve bolted joint performance. An ex ...

ELSEVIER SCI LTD2020