Publications associées à Laboratoire du génie parasismique et dynamique des structures

Influence of model uncertainty and long term deformations in action effects calculation in reinforced concrete structures

Most codes of practice adopt a semi probabilistic design approach for the dimensioning and assessment of structures. Accordingly, structural safety is ensured by performing limit state verifications using design values determined with adequately calibrated ...

EPFL2024

Experimental Investigation on Size-Effect of Rubble Stone Masonry Walls Under In-Plane Horizontal Loading: Overview and Preliminary Results

Katrin Beyer, Savvas Saloustros

Rubble stone masonry is a common construction typology of historical city centres and vernacular architecture. While past earthquakes have shown that it is one of the most vulnerable masonry construction typologies, there are few experimental campaigns giv ...

2024

Seismic Testing of Adjacent Interacting Masonry Structures – Analysis of a Blind Prediction

Katrin Beyer, Igor Tomic, Andrea Penna

Masonry aggregates, which emerged as layouts of cities and villages became denser, make up historical centres all over the world. In these aggregates, neighbouring structures may share structural walls that are joined at the interfaces by mortar or interlo ...

Springer2024

Short-term behavior of glass fiber-polymer composite bending-active elastica beam under service load application

Thomas Keller, Tara Habibi, Landolf-Giosef-Anastasios Rhode-Barbarigos

Bending-active elastica beam is a structural configuration that is based on the elastic deformation of an initially straight beam. This deformation occurs when horizontal displacements are applied to a sliding support, causing the beam to bend into an arch ...

2024

Reducing uncertainties in response predictions of earthquake-damaged masonry buildings using data from image-based inspection

Ian Smith, Katrin Beyer, Bryan German Pantoja Rosero, Mathias Christian Haindl Carvallo

Image information about the state of a building after an earthquake, which can be collected without endangering the post-earthquake reconnaissance activities, can be used to reduce uncertainties in response predictions for future seismic events. This paper ...

Springer2024

Shear and steel-fibre reinforcement for the punching resistance of flat slabs at internal and edge columns

Diego Hernández Fraile

Reinforced concrete flat slabs consist of a continuous, thin concrete plate that rests on a grid of columns. The supporting surface of the columns is very small compared to the floor plan dimensions, leading to concentrations of shear forces near the colum ...

EPFL2024

Numerical Modeling of FRP-Strengthened Masonry Structures Using Equivalent Frame Models

Katrin Beyer, Francesco Vanin, Ivana Bozulic

The present study focuses on enhancing the seismic resistance of existing masonry structures. To that aim, the use of fiber-reinforced polymer (FRP) strengthening serves to improve structural behaviour by attaching FRP strips to the masonry walls. Despite ...

Springer2024

Instabilities in Elastic and Magneto-Elastic Beams and Shells: from Shell Buckling to the Design of a Programmable Braille Reader

Arefeh Abbasi

In this thesis, we conduct a comprehensive investigation into structural instabilities of both elastic and magneto-elastic beams and shells, resulting in a creative proposal to design a programmable braille reader. Methodologically, we combine numerical si ...

EPFL2024

Experimental and analytical investigation of shear-reinforced concrete and dowel action

Marko Pejatovic

Codes of practice can be overly conservative, particularly for the shear resistance of reinforced concrete beams with shear reinforcement when large loads act close to supports. This thesis addresses the topic by proposing a refined design approach based o ...

EPFL2024

FLO:RE – A new floor system made of reused reinforced concrete and steel elements

Corentin Jean Dominique Fivet, Numa Joy Bertola, Maléna Bastien Masse, Célia Marine Küpfer

Carefully extracting reinforced concrete (RC) elements from soon-to-be demolished structures and reusing them as load-bearing components is an emerging circular low-carbon alternative to building new structures. As floor construction typically accounts for ...

IABSE2024

Contributions to rebar-to-concrete interaction and its structural implications for design and monitoring applications

Enrique Corres Sojo

Bond between reinforcing bars and concrete has been the focus of extensive research over the last century. This is well-justified as the functioning of reinforced concrete intimately depends on the interaction between rebar and concrete, as for example cra ...

EPFL2024

Influence of fiber orientation on the tensile behavior of UHPFRC and reinforced UHPFRC under static and fatigue loadings

Jian Zhan

Ultra-high performance fiber reinforced cementitious composite (UHPFRC) is a modern class of cementitious building materials. Because of its superior mechanical properties and durability, it is increasingly used globally to rehabilitate, strengthen and mod ...

EPFL2024

Model uncertainties in action effects and load bearing capacity calculation in statically indeterminate reinforced concrete structures

Aurelio Muttoni, Alain Nussbaumer, Xhemsi Malja

For the dimensioning and assessment of structures, it is common practice to compare action effects with sectional resistances. Extensive studies have been performed to quantify the model uncertainty on the resistance side. However, for statically indetermi ...

Ernst & Sohn2024

A Softening Constitutive Law and Gradient-Inelastic Fiber-Based Element for 3-Dimensional Frame Simulations Under Seismic Excitations

Diego Isidoro Heredia Rosa

Steel frame structures are essential components of modern infrastructure. Understanding their behavior under seismic loading is critical for ensuring public safety and minimizing damage that occurs during earthquakes. To accurately predict the response of ...

EPFL2024

Experimental investigation of dowel action in reinforcing bars using refined measurements

Aurelio Muttoni, Marko Pejatovic

In typical reinforced concrete design, reinforcement is designed to carry axial forces, but it can also resist transversal forces by dowel action. This is usually neglected for simplicity's sake in the design phase, but it can be accounted for either expli ...

Ernst & Sohn2024

Estimation of the bar stress based on crack width measurements in reinforced concrete structures

Aurelio Muttoni, Enrique Corres Sojo

Estimating the stress of reinforcing bars and its variations in service conditions can be useful to determine the reserve capacity of structures or to assess the risk of fatigue in the reinforcement. This paper investigates the use crack width measurements ...

Ernst & Sohn2024

Dataset for "Complexity of crack front geometry enhances toughness of brittle solids"

John Martin Kolinski, Chenzhuo Li, Xinyue Wei

This data package supports the publication 'Complexity of crack front geometry enhances toughness of brittle solids' by Xinyue Wei, Chenzhuo Li, Cían McCarthy, and John M. Kolinski Nature physics (2024) - https://doi.org/10.1038/s41567-024-02435-x DOI: 1 ...

Zenodo2024

Quantifying the Unknown: Data-Driven Approaches and Applications in Energy Systems

Paul Scharnhorst

In light of the challenges posed by climate change and the goals of the Paris Agreement, electricity generation is shifting to a more renewable and decentralized pattern, while the operation of systems like buildings is increasingly electrified. This calls ...

EPFL2024

Mesh-based topology, shape and sizing optimization of ribbed plates

In this paper, we present a new parameterization and optimization procedure for minimizing the weight of ribbed plates. The primary goal is to reduce embodied CO2 in concrete floors as part of the effort to diminish the carbon footprint of the construction ...

Springer2024

Reusability assessment of reinforced concrete components prior to deconstruction from obsolete buildings

Corentin Jean Dominique Fivet, Maléna Bastien Masse, Julie Rachel Devènes

A large part of building demolitions is motivated by purely socio-economic reasons. Hence, about-to-be-demolished structures, commonly made of reinforced concrete, very often present no or little degradation. When adaptive reuse of the entire building is n ...

2024